Admiral Washer Parts

Admiral Appliance Parts

Popular Admiral Washer Parts

DOOR STRIKE
$12.92
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX16218028
Manufacturer Part Number
W11457841
Fixes these symptoms
  • Lid or door won’t close
  • Locking Issues
  • Will Not Start
  • See more...
Suspension Spring
$8.00
In Stock
Fix Number
FIX11743345
Manufacturer Part Number
WP63907
This suspension spring is a genuine OEM replacement part for a variety of washers and washer-dryer combos. The primary purpose of the suspension spring is to support the outer tub and keep the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. This part is approximately 2 inches in length when compressed, made of durable metal, and is sold individually. For this repair, you will need a 1/4 nut driver, putty knife, flat blade screwdriver, and a pair of needle-nose pliers. Before you begin, disconnect the power, fill hoses, and drain hose to give you easy and safe access (drain hose may release some water, have a small container or towel near by). Your appliance contains 3 suspension springs, so keep this in mind if you need to order multiple of this part. We suggest you purchase several at a time, as they can be very useful to have on-hand.
Fixes these symptoms
  • Leaking
  • Shaking and Moving
  • Spinning Issues
  • See more...

Installation Instructions

CARLOS from EL PASO, TX
just to understand the type and different model videos
exactly as the video mentioned, just need to explain if some models are alike or different using the same part numbers will be awesome.in my case my washer had the screws in different areas to disassemble and Assembly the spare parts, other than that beautiful idea in sending the link video with the email confirmation let me tell you first class and top of the line customer service rated 5 Stars Read more...
Drive Hub Kit
$33.90
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX6012095
Manufacturer Part Number
W10528947
The drive hub connects the basket of your washer to the transmission shaft, which in turn allows the basket to spin. If your washer will not agitate, spins slowly, or is excessively noisy, it may require a new drive hub assembly. This genuine OEM kit comes with a new hub and a fork holder. To replace this part, you will need to remove the agitator from the tub to expose the hub assembly. Use a flat blade screwdriver to remove the fork shaped holder, and then remove the screws holding the hub assembly to the transmission shaft. Place the new hub onto the shaft, and rotate the washer tub to line up the holes. Once lined up, drill the screws back into place. Please note that this kit does not come with replacement screws, so you will need to reuse the ones from the old hub. The new fork holder is then put through the slotted opening, using a small hammer to tap it into place. Once you have installed the new part, be sure to follow the instructions on the pamphlet provided with the hub to calibrate your washer.
Fixes these symptoms
  • Shaking and Moving
  • Spinning Issues
  • Spins slowly
  • See more...

Installation Instructions

Dallas from BUCKLIN, KS
Washer would not agitate or spin correctly.
Removed the agitator. Removed the plastic clip. Remove 6 screws and pulled off hub. You have to remove the plastic cap on top of agitator to femoe the cap crew, first. Read more...
★★★★★
★★★★★
10 Reviews
Fix Number
FIX334650
Manufacturer Part Number
285811
This is an OEM agitator repair kit that includes an agitator cam, four directional cogs, a bearing, thrust spacer, inner cap seal, and washer. These parts are found inside the agitator auger near the top. This kit is used when the top portion of the agitator is not moving correctly but the bottom part is. The agitator is subjected to a lot of force during the wash cycle, so it is common for this part to wear over time, especially if you are consistently over-loading your washer. If your model has a softener dispenser, it will need to be removed to perform this repair. Agitator grease is recommended for this repair, but is not included in this kit.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Leaking
  • Marks left on clothes
  • See more...

Installation Instructions

Jerry from Aransas Pass, TX
Agitator not working correctly and leaking from somewhere underneath.
I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future. Read more...
Suspension
$113.47
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12347546
Manufacturer Part Number
W11130362
Fixes these symptoms
★★★★★
★★★★★
7 Reviews
Fix Number
FIX1485646
Manufacturer Part Number
285753A
This is an OEM direct drive motor coupling, which provides a cushioned connection between the transmission and the motor shaft. This is the newer version of this part, made with new metal sleeves for added strength. It is located between the motor and transmission on direct drive washers with no belt. If the drive system seizes, the coupling is designed to break to prevent the drive motor from damage. Consequently, this part may need to be replaced as your appliance ages. Never overload your washer, as this can speed up its deterioration. Symptoms of a faulty motor coupling include a washer pumping but not spinning, slow spinning, the washer not agitating, and unusual noises. This coupling kit contains all the parts necessary to replace your existing direct drive motor coupling. Please note, that after replacing the motor coupling your washer may smell like burning rubber for the first few uses, this is entirely normal as the part becomes acclimated to the machine. Each is sold individually.
Fixes these symptoms

Installation Instructions

Joseph from Burnsville, NC
Washer would not spin or agitate
First, I found it very easy to follow the help on your web site to determine the most likely parts that would cause my problems. The direct drive motor coupling could be the cause of both problems. Also the agitator repair kit was the most likely cause of the agitator problem, So, I ordered both parts. When AI received the parts there were videos included instructing every detail for installation. I just followed the video for the direct drive motor coupling and both problems were solved with the one part. It took about 30 minutes and was a simple installation. .Thanks for your good service. It saved me a service call or maybe a new washer and dryer set. Read more...
★★★★★
★★★★★
2 Reviews
Fix Number
FIX10057144
Manufacturer Part Number
W10721967
The washer drive pulley kit is also known as a replacement clutch assembly, or a cam kit. The drive pulley is found at the bottom of your washing machine, mounted to the drive shaft. Common symptoms indicating an issue with the part include the washer having difficulty with the wash and spin cycles, or is making a lot of noise. It is likely that the splines on the assembly have become stripped, and the assembly will need to be replaced. To do this repair you will need to disconnect the power and water supply to your washer, and place the washer on its back to access the drive shaft. This kit contains 6 different certified OEM parts that make up the clutch assembly, which includes the pulley, 13 mm nut, cover, gear, cam, and spring.
Fixes these symptoms
  • Burning smell
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • See more...
Clutch Assembly
$27.55
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX334641
Manufacturer Part Number
285785
This is a genuine OEM replacement clutch assembly for your washing machine. A clutch assembly, also known as a clutch or a washer clutch, is responsible for spinning the tub during the spin cycle. If the clutch becomes worn and is no longer operating properly, your clothes will remain soaked after the cycle is finished. Some other signs it is time to replace the clutch is if your washer is noisy while running, there is a burning smell, or the machine is shaking excessively. This kit comes with the clutch, brake cam driver, spring, retaining ring, and a nylon anti-rattle clip. Before beginning this repair, be sure to disconnect the power and water supply to your machine. Depending on your washer model, you may need an additional person to help lower the machine onto its back, as access to the drive shaft to change the clutch assembly may be easiest through the bottom of the appliance.
Fixes these symptoms
  • Burning smell
  • Spinning Issues
  • Spins slowly
  • See more...

Installation Instructions

Paul from Mobile, AL
would not spin
well i replaced a lot of parts..but i think it was the the lid switch. but now its brand new..Thanks Read more...
Washing Machine Suspension Rod Kit
$76.15
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX11703290
Manufacturer Part Number
W10780048
The suspension rods help to keep the tub in your washing machine stable and secure while cycling through your laundry. If your washer is excessively vibrating, moving around, or very loud when operating, there may be an issue with your suspension. This authentic OEM replacement kit includes 4 rods, 4 suspension balls, and 4 bushings. The parts come assembled and ready to be installed. You will need to disconnect the power supply, water inlet and drain hoses from the washer before beginning this repair.
Fixes these symptoms

Installation Instructions

David from Garden Grove, CA
Shaking violently on spin cycle.
I removed the top section and control panel(disconnected one hose and electrical connector . Layed complete washer on back side. Slid washer bucket up towards the top. Installed all 4 rods into place. Then tipped washer back on its legs and reassembled. Rechecked washer was level. Note: I inspected the old rods and compared to new and found no issues with old ones. Most likely weak springs. Runs like new now. Also noticed before complete barrel was hanging low and is now higher with new rods installed. Read more...
Suspension Rod Kit
$82.16
In Stock
Fix Number
FIX11703288
Manufacturer Part Number
W10780045
Fixes these symptoms

Admiral Washer Appliance Types

Related Admiral Washer Parts

Popular Admiral Washer Models