Jenn-Air Washer Dryer Combo Parts

Jenn-Air Appliance Parts

Popular Jenn-Air Washer Dryer Combo Parts

★★★★★
★★★★★
10 Reviews
Fix Number
FIX1570070
Manufacturer Part Number
12001541
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Front Glide Kit
$14.69
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX1804752
Manufacturer Part Number
306508
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may need to replace the front glides. This genuine OEM front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. We recommend replacing both sets of glides at the same time, which will require the purchase of two kits. To complete this repair, you will need a Philips screwdriver and a 5/16 nut-driver to remove the front panel and the bulkhead of the dryer, a drill with a 1/8-inch bit to remove the old rivets, and a rivet tool to install the new ones. Please ensure that you disconnect the power supply to your dryer before beginning this repair. While you have the appliance opened, we recommend vacuuming out any lint and debris, and inspecting the felt around the bulkhead and replacing if necessary.
Fixes these symptoms

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
★★★★★
★★★★★
9 Reviews
Fix Number
FIX11757542
Manufacturer Part Number
WPY312959
This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Roller Shaft
$9.80
In Stock
Fix Number
FIX11743031
Manufacturer Part Number
WP6-3129480
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while operating, or will not tumble at all, you may need to replace the roller shaft. You may also want to inspect the drum rollers at the same time and replace them if necessary. Replacing the roller shaft will require that you remove the front panel and the drum from the dryer. Please ensure that you disconnect the power supply before beginning this project. The tools you will need include a Philips screwdriver, a 5/16-inch nut driver, a pair of snap-ring pliers, and a 9/16-inch wrench. The roller shaft is an authentic OEM part.
Fixes these symptoms

Installation Instructions

Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...
★★★★★
★★★★★
3 Reviews
Fix Number
FIX2200270
Manufacturer Part Number
Y303836
The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.
Fixes these symptoms

Installation Instructions

Erik from Belvedere, CA
Noisy 'rattling' sounds from Dryer ->bad blower fan wheel
Watched the video - really helped me get prepared. Very simple repair: first, unplug power! Removed front panel 2 screws & slowly pulled panel outward to release top clips (2min). At unit bottom, removed the blower fan grey cover (7 screws, 3min). Pulled spring washer (careful not to bend) from shaft and removed spring clip on blower fan wheel (5 min). Installed new blower fan wheel onto shaft with washer&clip. Reinstalled blower cover/screws and front panel/screws. Total time about 15min. Thanks for an easy, inexpensive fix! Read more...
Belt Kit
$41.21
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX2005284
Manufacturer Part Number
12112425
Over time, the belts in your washer can either stretch out and sag, or become brittle and snap. When this happens, it can result in the belt losing its grip and will not be able to spin or drain the tub. If this happens, the belts will need to be replaced. This OEM belt kit includes the drive belt and the pump belt, which are both V-shaped, and made of black rubber. The pump belt is located between the motor and pump under the washer, and the drive belt is looped around the drive and motor pulley at the bottom of the machine. This repair is easiest to complete if the washer is placed on its back, and you will need to disconnect the power and water supply.
Fixes these symptoms

Installation Instructions

George from Burnt Ranch, CA
Washer motor was actuating but machine whined and emiitted smell of burning rubber. Agitator did not turn.
Disconnect washer from power, water inlet, and drain. Move machine out from installed position. Tilt machine against wall, back panel to wall. Remove belts, inspect the pump and agitator belts for excessive wear, burnishing, cracking. Remove front panel. Advance the water pump manually to confirm it is not stuck or clogged. Advance transmission (large counter weighted object on spindle immediately below tub) shaft to confirm freedom of movement. If it doesn't move, you should consider a new machine. Transmission repair is above DIYer level and too costly on older machine. If transmission shaft turns by hand, replace belts if necessary, and confirm tension to manufactures recommendation by adjusting position of the water pump. Reposition machine and attach water inlet, outlet, and power. Activate machine and confirm operation. Read more...
Lint Filter
$25.03
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX11741039
Manufacturer Part Number
WP33001003
This lint filter is a genuine OEM replacement part for your dryer. The lint filter is used to trap debris and prevent it from clogging up your dryer vents. If your lint filter has become damaged it should be replaced. Using your dryer without a lint filter can be a serious fire hazard, along with decreasing the efficiency of the machine. No tools are required to replace this part, simply pull out the old filter and slide the new one into place.
Fixes these symptoms

Installation Instructions

James from SANTA ROSA, CA
My drier was making rumbling noises.
I followed the video instructions, which were great by the way. Pretty easy to remove the front panel, then housing, then belt, then drum to expose drum support rollers and shafts. Removed old and replaced with new after cleaning lint up a bit. Unfortunately, there is still a bit of a rumble when the drier starts up. I fully expected the changed out parts to make a difference, but it was only a modest improvement. I need to do further trouble shooting and diagnosis. Read more...
Idler Pulley Wheel
$19.25
In Stock
Fix Number
FIX11743028
Manufacturer Part Number
WP6-3037050
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
Fixes these symptoms

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Fix Number
FIX11740771
Manufacturer Part Number
WP314820
This front or rear dryer drum felt seal is seventy-nine and a half inches long.
Fixes these symptoms

Installation Instructions

Orrin from La Canada, CA
Dryer makes horrible noise but drum still turns.
The old dilemma is whether to fix a >20y/o dryer, or just buy a new one. With minimal effort, it was easy to find the source of the noise by manually turning the drum. Noise in the front turned out to be the blower wheel which is located right in the front of the dryer. Removing about 6 screws shows the motor shaft wore out the plastic center of the blower wheel and so the blower wheel was not spinning properly and bouncing around in the housing. Typing in the Model # in PartSelect.com gave me the whole diagram and exactly what to order. Since I had the dryer apart anyway, I decided to go ahead and replace the felt seals and drum/motor belt and front glides. Easy instructions to do all of this is available on multiple YouTube videos. The only caveat is some of these items are held in w/ snap rings. It's possible to deal with snap rings using a small screwdriver and pliers but having special snap ring pliers makes this step a whole lot easier. In my case the drum support rollers and belt tensioner roller turned out to be fine and only needed some lubrication. Also, in this particular model, the felt seals are held on w/ sheet metal tabs and do not require the expensive heat resistant glue. All parts installed, dryer back together and works perfectly on the very first try! Saved me a ton of money and the wife is happy, thanks to this site! Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX11757538
Manufacturer Part Number
WPY312527
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
Fixes these symptoms

Installation Instructions

Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...

Jenn-Air Washer Dryer Combo Appliance Types

Related Jenn-Air Washer Dryer Combo Parts

Popular Jenn-Air Washer Dryer Combo Models