International Dryer Parts

International Appliance Parts

Popular International Dryer Parts

★★★★★
★★★★★
10 Reviews
Fix Number
FIX1570070
Manufacturer Part Number
12001541
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Front Glide Kit
$14.69
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX1804752
Manufacturer Part Number
306508
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may need to replace the front glides. This genuine OEM front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. We recommend replacing both sets of glides at the same time, which will require the purchase of two kits. To complete this repair, you will need a Philips screwdriver and a 5/16 nut-driver to remove the front panel and the bulkhead of the dryer, a drill with a 1/8-inch bit to remove the old rivets, and a rivet tool to install the new ones. Please ensure that you disconnect the power supply to your dryer before beginning this repair. While you have the appliance opened, we recommend vacuuming out any lint and debris, and inspecting the felt around the bulkhead and replacing if necessary.
Fixes these symptoms

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
★★★★★
★★★★★
9 Reviews
Fix Number
FIX11757542
Manufacturer Part Number
WPY312959
This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Roller Shaft
$9.80
In Stock
Fix Number
FIX11743031
Manufacturer Part Number
WP6-3129480
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while operating, or will not tumble at all, you may need to replace the roller shaft. You may also want to inspect the drum rollers at the same time and replace them if necessary. Replacing the roller shaft will require that you remove the front panel and the drum from the dryer. Please ensure that you disconnect the power supply before beginning this project. The tools you will need include a Philips screwdriver, a 5/16-inch nut driver, a pair of snap-ring pliers, and a 9/16-inch wrench. The roller shaft is an authentic OEM part.
Fixes these symptoms

Installation Instructions

Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...
★★★★★
★★★★★
3 Reviews
Fix Number
FIX2200270
Manufacturer Part Number
Y303836
The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.
Fixes these symptoms

Installation Instructions

Erik from Belvedere, CA
Noisy 'rattling' sounds from Dryer ->bad blower fan wheel
Watched the video - really helped me get prepared. Very simple repair: first, unplug power! Removed front panel 2 screws & slowly pulled panel outward to release top clips (2min). At unit bottom, removed the blower fan grey cover (7 screws, 3min). Pulled spring washer (careful not to bend) from shaft and removed spring clip on blower fan wheel (5 min). Installed new blower fan wheel onto shaft with washer&clip. Reinstalled blower cover/screws and front panel/screws. Total time about 15min. Thanks for an easy, inexpensive fix! Read more...
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11741110
Manufacturer Part Number
WP33002535
If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. This genuine OEM multi rib dryer drum belt measures approximately 91 and 5/8-inch in length and is 3/8-inch wide. It is made of black rubber and have five ridges, helping it to grip to your dryer drum.
Fixes these symptoms

Installation Instructions

Tim from PORTLAND, OR
Dryer was a bit noisy with a full load of wet clothes
As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this. Read more...
M Series New Style Coil Kit
$30.86
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX334310
Manufacturer Part Number
279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms

Installation Instructions

Dennis from ALISO VIEJO, CA
Dryer ran but did not dry clothing.
Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench. Read more...
Retaining Ring
$7.87
In Stock
Fix Number
FIX11746909
Manufacturer Part Number
WP9703438
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.
Fixes these symptoms

Installation Instructions

Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX11743032
Manufacturer Part Number
WP6-3700340
If your dryer is making excessive noise, or it will not tumble, there may be an issue with the idler pulley wheel. The idler pulley wheel is attached to the idler bracket and is used to secure the dryer drum belt, which helps the drum to rotate. This genuine OEM part is made of white plastic with a metal center bearing. Over time this part can become worn, which will result in your drum not rotating or screeching noises when it spins. If this happens the idler pulley wheel should be replaced. Before beginning this repair, please be sure to disconnect the power supply to your dryer. To complete this job, you will need a Philips screwdriver, a 5/16 nut driver, a pair of Channellock pliers, and a small flat blade screwdriver.
Fixes these symptoms

Installation Instructions

Tim from PORTLAND, OR
Dryer was a bit noisy with a full load of wet clothes
As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this. Read more...
Fix Number
FIX11741074
Manufacturer Part Number
WP33001807
This seal can be used for the front or rear drum. Adhesive is NOT included. For adhesive search: WPY055980
Fixes these symptoms

Installation Instructions

James from EASTON, PA
The dryer was making a loud noise.
The felt around the front of the drum was coming off. This caused the drum to grind against the front end of the dryer. Had to remove the front and the drum. Replaced it and reintalled. All is good again. I could not have done this without the assistance of your "How To" videos. After watching it was very clear the steps needed to accomplish this repair. The hinge hole cover was cracked that was "Very Easy" to replace. All parts puchased at this site. Read more...

International Dryer Appliance Types

Related International Dryer Parts

Popular International Dryer Models