ITW4771EW0 Inglis Washer - Instructions

My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!

Removed old one (2 screws) slid in place and screwed in.

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

I watched the video and for the most part the first part of the repair went well. I carefully stored the screws, but despite what the video suggested the part did NOT just slide out. Upon further inspection I discovered two small screws in the top of the valve housing affixing it to the machine. Since it was to narrow an are to use a driver I was forced to remove the housing that holds the timer, which involved removing the knob and a small screw. On each side of the housing was a metal clip and true to form I was able to loosen one side but the other the clip launched into orbit. After a thorough inspection of the floor I found said clip. I was then able to remove the housing and loosen the two screws. Of interest is the fact that the new part had molded places for screws different that the video. After that replacing everything went smoothly and I was able to hook up the washer as the repair was successful.

Trying to follow the instructions according to the video was easy enough until the part where I had to remove the control panel for access to the screws holding the inlet valve. I don't have a putty knife, so I had a bit of trouble trying to remove the panel. I found another way. There are screws on the left and right sides which hold the control panel to the side pieces holding it to the body. If you remove the screws and use a pick or flathead screwdriver to carefully pull up on the tabs below the screws while gently pulling the control panel away, it will easily pop off with a rotational movement. The panel is centered into its location via two plastic pins molded into the side panels, so be aware of them and try to avoid breaking them. They'll help you get the panel properly positioned during reassembly, which is simple. You'll see all this easily if you take the time and look. Don't be in a rush. To reassemble, line up the panel with the plastic pins and rotate it into position. The tabs slide easily into position and lock the panel into place. Just don't forget to reinstall the screws. Removing the panel in this manner added a bit of time to the repair, but not a lot. It's still a fast repair overall. Everything else was exactly like in the video. Well, almost. I had no difficulty whatsoever with sliding the new valve into place. But once the job was done the sounds coming from the washer during the filling stages ceased. Turns out the screens in the inlet valve were getting stopped up with lime.

Part fixed it perfectly.

I figured out through the process of elimination that the problem was the rubber plunger that the solenoid opens and closes. I couldn’t fix just the plunger so I replaced the whole water inlet valve and the cold water worked perfectly after that. Even though it was a little tough to diagnose the problem it was very easy to replace the part once I found out what it was that was wrong.

Took the Cover off and installed belt.

Im a 58 year old single woman. Swap out of pump motor was so easy. Took less than 15 min. Ordered the part on Tuesday it came the next day. I installed it and did 4 loads of laundry.
Great company.

followed the instructions on the video, very easy install

I just drained the washer and unscrewed the 3 screws unhooked the hose clamp and installed the new one attached the hose and hose clip. Really easy. Took longer to try up water in floor than installing.

Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast