AA5420 Amana Washer - Instructions

To remove the drive bell, I drilled numerous holes through the top and split it apart with a screwdriver. The hub was really stuck and due to the unavailability of a 6" puller, I was forced to drill holes in the center section, tap the holes and use a harmonic balancer puller, PB Blaster, and propane torch to remove the hub. After removing the hub, I found small holes rusted through the outer tub. These I repaired with JB WaterWeld quite successfully. The new parts were well made and went on easily in about 45 minutes.

Released idler pulley and replaced belt

After removing the front panel I was able to reach the bolts holding the brake pads in place. Without the above mentioned ratcheting end wrench it would have been very difficult to start the bolts while replacing them. I would probably consider removing the motor if I had to do this again. It would give a lot better access. no real difficulty other than hard to reach.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

remove agitator then remove center bolt from hub, match bolt with longer bolt so that gear puller will work. install bolt and gear puller and twist top of gear puller until hub is removed. remove old seal ,use sand cloth or emery cloth to remove all deposits from shoulder. make it shinny, use some dawn dishwashing soap to line the inside of the new seal at the bottom and slide into place.take a piece of 2" PVC about 4" long and slide over the top of the seal and tap with a rubber hammer until seal is seated firmly on shoulder. look to see that there are no gaps with a inspection mirror or a make-up mirror.If their are no gaps ,install the hub and tap on the new hub with the rubber hammer. the hub will not seat all the way down so use the old bolt to pull it down, now take out the old bolt and install the new one, this is because the new one has lock tite on it ,your done!

removed four 5/16 screws and two hose clamps. This released the pump and belt. With the pump on the bench, I removed a c-clip and removed the pulley. Just reverse the process and it was back together in about 15 minutes---total job.

Took the plate off the back of the timer. Unscrewed two screws from the timer, then removed the plastic knob in front of the washer and removed the electrical plug from the timer. Then just reversed the process to install the new timer.

It was easy, All we had to do was loosen up the tension on the pump, put the new belt back on and put the tension back on the pump motor by sliding it to the side and re tighten the screws to hold the pump tight.

took the drive belt to the pump off then put the belt for the drum on .then put the belt for pump back on. basickly this unit is one of the easist to work on

Taking the hub out was a promblem because, with a puller it did not come out. It broke off while pulling out we had to drill it
out had to brake off.You need a 1 1/2 inch deep socket with a impact wrench. It was a hassel but got done. I replaced the whole seal kit and it is still leaking it leaks from the bottom of the tub. It leaks worse when it has a heavy load I dont know what to do.Need help.

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.

i had to remove the broken plastic pieces from behind the stem that was holding the knob that took a litle time been careful not to break anything else. getting the right replacement part it help a lot. .

Removed the cover on the washer controls. Loosed the knob and popped it off. Then disconnected the plug and replaced with the new part. Put th ekonb back on and closed it all up. It was pretty easy. Took longer to reomove all the screws than it did to remove and replace the part.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.