GUD24ESSJ0WW General Electric Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard A. from Little Elm, TX
- Parts Used:
- WD21X10261
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not start
Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Helena, GA
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Needed to change the felt due to a squeaking noise.
I'm a 90 pound mother of 4you and was able to fix this problem all by myself. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Daytona Beach, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would Not Start
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Philadelphia, MS
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer wasnt drying as fast and was making a lot of noise.
Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.
Was this instruction helpful to you?
Thank you for voting!