GBS309PVB02 Whirlpool Wall Oven - Instructions

Don't, Don't, Don't!!!!!!! call a repair man to replace the thermo fuse. If you are able to use the T.V. remote and crack a twist top off a cold beer, then you can DO this. I am 47 years old and half retarded and my 84 year old neighbor and I completed this task in 12 minutes. Turn off the breaker panel, pull the oven out, (it is hard wired). We placed it on a 4 wheeled dolly. Unscrew 11 screws, pop the panel. The fusee is at the top/center with two screws holding it. Pull the two wires off, screw it back in place. Put back the panel & 11 screws. Put the oven back in place. Turn on the breaker and you are done. PS Tell your wife or girl friend this might take an hour or so. Send her to the store for a six pack & steak.

Thanks to those who replied to my intitial distress call...because of them I had the courage to attempt the repair.
First I flipped the main electrica breaker.
then I removed the screws from the main door. The next step was to pop out the pins holding the hinges. I couldn't do that no mater how much WD-40 and lubricant I used, or how hard I tapped center mass.....SO I took all the OTHER components out staring with the side facings. (1 screw right left and 2 for bottom.)
Next I took the screws holding the door together out -- then the two screws holding the clamps on the bottom of the door. At this point I lifted off the the front facing of the door by the handle and placed it with its glass, to the side.

I then had access to the two inside panes of glass. They are secured with a metal plate screwed into the metal of the inner door. When I removed the two screws securing the plate, two plates dropped to the floor and it was fortunate I was holding the glas securly as it two would have dropped.
Next, I cleaned each of tpieces of glass with oven cleaner and set them carefuly to the side.(they were crusted with brown) Lastly I wiggled the broken glass out of the small inner window, working from both the inside and the outside of the window. Becuase I couldn't open out the door.. this was an extrememly time consuming activity..but do-able.

Once the inner glass was in screwed one of the screws o the clamp plate so I could rest the glass while screwing in the second screw. Once screw two was in place I took out the retaining screw and replaceed in with the glass clamped between. Aftern that the tough stuff was done and I just reassmebled all the door parts.

This SHOULD have been much simplier! IF I could have removed the hinge pins as directed.

Anyway, mission acomplished. Oven works fine.
Thanks!

I removed eight screws to disassemble the oven door. I removed the old insulation and the brackets that held class panel in place. I installed the new insulation, tempered glass and reassembled the oven door.

No repair - just open the box and put the rack in my oven - voila - repaired!!! BUT let me tell you PartSelect sent the right part at the best price and I received it even ealier than I expected!!! I can DEFINITELY recommend these people and I do that very sparingly!!!! THANX!

The repair was pretty simple. I removed the old door front from the oven door, there were only 4 screws to remove. I then removed the handle off the old door and placed it onto the new door front. Finally, I placed the new door front over the oven door lining up the srew holes and screwed them in. I would recommend attaching the bottom plates first to make sure the oven door front and oven door are flush at the bottom.

Pull it away from the wall and take everything off the back. Unscrew the element cover, cut through the insulation and remove the part. Not easy, watch for sharp sheet metal edges

Kept removing screws and pulled things out until I got to the inner glass.
Yep, clueless and never did this before.
Put everything back in the opposite order of taking it out. Wala it's fixed.
Repair people wanted over $300 for parts and labor. However, with Partselect I was able to fix it for under $50.00 Well worth it!
Carmen

The inner glass on the wall oven shattered (apparently a common problem). Rather than look at a new $2-3,000 oven, I found the part for around $30. The repair was actually fairly easy, just had to be careful with the glass panes.
I did not remove the door completely, just worked on it either open or closed, depending on the step. First I loosened the two screws on the bottom of the door (when closed). Then I removed the four screws on the inside of the door and the two on the top part of the door (2). This allowed the outer panel to slide out and be removed.
Then there are two middle panes, held on by small clips with two screws in each. Remove one at a time, being careful not to drop any of the glass on the floor! Remember the order of the glass and the clips, so you can replace in the same order. (Now's a good time to clean all of the inner panes also, and to vacuum out the interior of the door.)
Lay these panes aside, and you should be to the broken inner pane, held on by a metal panel--again remove a couple screws, the panel, and remove all the broken glass. Be careful to retain all the insulation around the glass, and replace the glass, then the metal panel, the inner panes, and the outer door panel in that order. The outer panel should slide into place if you remove one clip and screw and start on one side, then replace the clip.

Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.

Unlock door hinge locks. Rmv door from oven by orienting to a 45 degree angle and slightly lifting up and out. Rmv outer Stainless Steel panel from oven door that has the broken glass. Rmv handle. Install new handle on outer door panel but don't over tighten. Place panel on oven door and install screws. When reinstalling door back on oven try to orient door at a 45 degree angle sliding in till you feel a slight bump. Try but don't force the door to the full open position and slide door latch locks back in place. Check the Kitchen-Aid website for better door rmv and install instructions.

Pull the end of the lens nearest the oven door out of the oven wall. Because our oven is several years old and the bulbs had not been previously changed, I could not pull the lens out with my hand, so used two small screwdriver under the metal tabs which hold the lens in place, the metal holder came out with the lens. Once the lens is removed, simply pull out the old bulb and, either while wearing surgical gloves or holding the bulb with a cloth (do NOT allow bare skin to touch the bulb or you will be replacing it again sooner rather than later), push the new bulb's pins into the socket. The lens then is simply pushed back into place.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

Open oven dooor. With a philip screw driver remove the gasket plate at the bottom of the oven holding the seal gasket. pull seal gasket away from oven seal channel and clean surface before installing new seal. align seal pins to to seal channel holes be sure not to twist the seal insert pins in one at a time.Install lower bracket however you may want to wet the fray ends of the seal gasket prior to screwing in plate to keep the ends from moving away from the bracket when scrwing it in place.

Read all the way through this once before doing it. It really helps in keeping pieces and parts separated. First I had to take off the oven door. Please do this as it will make your life so much easier! The owners instructions does a lousy job explaining how to do this. You need to insert a small Allen wrench into the holes behind the door hinge pin. Just stick them in there and leave them. If you don't have Allen wrenches you can use small nails or the like, but you have to put something into the holes. Close the door slowly, yes it will feel like you are going to break the hinges or the wrenches. When you get the door almost completely closed you should wiggle the door a bit by the handle and pull up. The door will come off. Once you get the door off you can get to work. Leave these wrenches in the hinge holes. You will need a flat surface big enough to lay the door down to work on it. Lay it down with the handle towards the surface and the broken glass facing you. Remove the 4 screws on the broken glass side, the 2 screws holding the brackets on the bottom and the 2 screws on the top of the door. You will need to wiggle the inside cover off because there are 2 little clips at the top you need to get it off of the outer glass door. You should have 2 separate pieces, the outer glass of the door and the inner tempered glass and sheet metal portion of the door. Set the outer glass door aside, somewhere safe, as you really don't want to have to reorder that part too! From there you can lay the door down with the broken inner door glass towards the work surface. Remove the screws and good pieces of glass and lay them down in the order you take them out. This helps putting them back together later. Keep the pieces together in sets so you know which set goes to each section. There should be 3 pieces of glass total in the assembly. You remove the screws and the 2 good pieces of glass. The inside door glass is accessible under a large piece of sheet metal held in place by little flanges cut into it. You can remove this sheet metal panel piece by wiggling it out away from under the hinges and away from the hinge end. There is a piece of insulation under there as well. Make sure you reseat it correctly when you put it all back together. If you don't it will stick out, and make things hard to line up. Pull the broken glass out, Put the new glass in and replace the sheet metal panel. At this point I would suggest putting the four screws you took out at the very beginning from the inside of the door back in. They keep the 2 hinge assemblies in place and they will be harder to line up if you don't. You need to work from the bottom side up but it's pretty easy to get the 4 screws back in. Don't be afraid to wiggle the pieces around so you can line up the holes. They need to line up so that the hinges line up back to the oven. Reverse how you took the other glass pieces out and put the door back together. Put the front glass piece back on and secure it in place with the bottom door brackets and screws and the top 2 screws. Lift the door unit back up by the handle and place it in the slots for the hinges exactly the way you removed it. You will feel it sort of catch when you pull the door open slowly. Remove the Allen wrenches and you are done.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland