10644029600 Kenmore Refrigerator - Instructions

We removed the old shelf. Put the new shelf in place and slipped the crisper tray on the new rails of the replacemnet shelf. The crisper no longer falls off the broken rails when you open it. We noticed the replacemnet shelf has metal rails and the original had plastic which is probably why it broke after heavy use over 12 years.

Removed 3 screws on the bottom of old ice maker in the fridge, slid out old ice maker, disconnected electrical cable,took out old ice maker. Take the plastic tray from bottom of old ice maker install on new ice maker, reconnect cable, slid in place, replace the three screws. About 3 hours later water ran in and new ice maker started to make ice. The only thing I missed was I didn't rinse out new ice maker before installation. If you don't rinse out new ice maker you have to throw away the first full bin of ice due to metallic taste.

Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

New part slipped right into the studs and fit perfectly

First removed one screw from the bottom right bottom side of the unit. Removed the door from the front of the unit. Pushed up the locking tab on the left underside of the unit and pulled the unit partway out. Removed the plastic cover ( that was retained by the screw removed and disconnected the electrical connection) and finished removing the unit from the freezer. Removed the remaining three screws from the bottom of the unit and installed on the bottom of the new unit. I then slid the new unit partially in and connected the wiring harness and slid the rest of the way in guiding the water line into thepocket which was taller than the origional unit. Reinstalled the wire protective cover with one screw and the front cover back on the new unit. Done and is working great.

There was a loud noise coming from the fridge - we ordered the new part it came a lot sooner than we excepted and we replaced it in about 20 minutes- the hardest part was my husband getting his hand in there to put the screws in- but a very easy fix.

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

first i put in a new water inlet valve it did not solve the problem i waited 3 days then ordered the ice maker i put it in an it still did not work after 3 days i put in water in the ice maker by hand it still did not work i gave up then to my surprise 4 more days it started working still not sure what was wrong but i am glad it works now this was about a two week process one tip on getting ice maker out is to take the door that's covers ice maker off no tools needed then remove three screws slip it in an out there is a helpful video for water inlet thank you mike b

After deciding it was the unit itself and not a water celenoid I ordered it from parts select. Instead of 3 to 5 business days it arived the next day after ordering. I had previously removed and reinstalled the ice maker while trouble shooting. It was easy to change it out, and works perfectly.

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

Remove ice maker from freezer, place on its side on table. Remove single screw securing coupling from shaft without removing shaft from housing. Remove old coupling, and attach new coupling using single screw.

This is a great time to completely clean the Ice maker bin and crusher unit.

I removed cleaned & re-ionstalled the same unit. It started to slowly make ice and then stopped. I repeated the above procedure again and it started to work normally. I will keep the replacement icemaker as a handy spare. I fear it will fail again in the near future.

Heating element broke and fried the rest of the parts had to take out the bad parts and put in the new ones and it worked. i have fixed this problem three times now.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

plastic warped in ,spaced out and, the socket snapped back in place.