3638698710 Kenmore Refrigerator - Instructions

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

The left side rail had broken where the screws secured it to the drawer. Your replacement part fits perfectly! In fact the drawer slides easier now than it did before!

I’d read that I should keep the original screws. They were a bit too big to fit the replacement part. A trip to the hardware store solved the problem and the new slide is now in place.

Your description and drawings for this part really helped me out!

Thank you so much for having this service available for my old but trusty refrigerator!

Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!

Easy

Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.

Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!

I replaced both the punp and water line. the website depicting the repair parts was the best i ever worked with. The parts were high quality delivered on time and easy to install. Total job cost $30 as opposed the cost of of a service man or a new refrig.

First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif

unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)

Slide rails are shipped without screws, therefor, must use old ones. TORX driver required for self tapping screws. Missing screw required trip to hardware store for replacement. Unable to match screw; had to improvise with a different type of screw.

I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.

Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy

removed the screws and then replaced the rails. Easy

If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!