CTX14CIBBLWW Hotpoint Refrigerator - Instructions

You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.

My wife had the cover changed before I got home from work. Perfect fit for a replacement part!

I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.

removed broken bin , slid new ice bin in closed door. I bought the complete part.

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

My son did it , and showed me what he did when he was finished.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts


L

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

The repair only required removing nthe old cover and installing the new one. What I was really surprised about is the time for delevery. I ordered the part on Friday morning around 11 AM and it was delevered by Fed Ex at 8:30 AM on Saturday morning. I am not sure how many locations they have, but this must have been close to Harrisburg, Pa.

first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"

Installation could not have been easier!