DTL18ICSURBS General Electric Refrigerator - Instructions

Installing the part repaired the fridge and freezer immediately.

Unplug refrigerator and turn water supply off to the ice maker. Remove the screws holding the bottom cardboard-like cover from the lower back of the refrigerator. Remove the water supply line to the old solenoid with 1/2 inch wrench. Unplug the two power supply wires to the old solenoid. Remove the screw that holds the solenoid to the back panel of the unit. After the solenoid is pulled out, remove the output hose with a 1/2 inch wrench. The configuration of the replacement solenoid is likely a little different than the original, but it seems to be rather universal and will fit back into place and perform properly. The new solenoid does not use a compression type nut to secure the output line. It's just a simple push-in connection. The wires may have to be rerouted a little, just keep them clear of the evaporator fan blades Reverse the removal procedure and you're done.

Removed fan housing from top of freezer, then the two screws holding the rest of it in place. Then two more screw and removed the vertical housing in back of freezer. two more screws and I was able to remove the whole back plate. I unplugged evap motor wire from back of freezer wall and unscrewed motor bracket. once motor was free, I removed the blade, unscrewed ground wire and installed new motor. I then plugged wire back in to ensure new motor worked and put everything back. Super Easy!!

replaced lights in refrigirator and freezer

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Pulled the fridge from the wall. Then shut the water line to the fridge off. Pulled the water line to the ice maker out the old grommet. Then a screw or two from the cover over the bottom back of the fridge, so I could get to the outlet valve kit. Only 1 screw was holding that. Then took the lines off the old outlet valve. Took the little hose off the grommet on the inside of the freezer that leads the water into the drip pan to the cube tray of the ice maker. Then grabbed pliers for the grommet on the top back of the fridge. And pulled and twisted alittle till it came out. It was alittle hard but got it out. Cleaned the out sticky tape off around the hole where the grommet connects. Hook the water like that goes to the grommet for the ice maker to the new grommet. Peeled the paper of the sticky tape for the new grommet. And placed it in. Then connected the rest of my water lines to the inlet valve. Put everything back the way it was. Then plugged and turned the water back on. And in 2hrs or so I had ice fall in the tray and continues to make ice no problems. “Note also I didn’t actually unplug my fridge I did it all why it was plugged. Thought it would be best to let you know. LoL but a small socket 1/4 with a 1/4 drive or worked. Also I think my grommet was harder to get out cuz it was froze due to the water leaking in the grommet.

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

I'm not a DIY-er, and wasn't sure a 20 year old refrigerator was worth the repair, but for $30 I could afford to be wrong. The swap is pretty intuitive, especially in my case since the problem was that the water tube from the valve to the ice maker had detached from the coupling. So I didn't have to cut anything off, just inserted the tube into the new valve. Reconnected the supply line, screwed the assembly back on the refer, and Bob's your uncle. Other than unloading some canned goods to lighten the refer, longest process was finding the right size nut driver in my disorganized tool tray. Be aware, there are NO instructions included with the part. Found a good video on you tube that confirmed the obvious. Glad I took a shot!

Removed the old water valve from back of refrigerator by using a screwdriver. Pulled water line off old valve that runs into the fridge and inserted it into the new part. I used a pair of pliers to take off water line that runs into the water valve from the house. Screwed the water line back onto the new valve. Took about 10 minutes.

Installation could not have been easier!

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker now works great.

i took the backing off with a screwdriver, cut the wires and put the 2 wires on that came with the thermostat. p.s. make sure you pull the power plug before you start.