EW23BC87SS5 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joshua from AKRON, OH
- Parts Used:
- 809069206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
condenser fan is no longer holding running speed
Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from Austin, TX
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
routine maintenance
slide old filter out and insert new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from REINHOLDS, PA
- Parts Used:
- 241804006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken built in bin hanger
Lift broken bin out and place new bin in place push down to make secure fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from FREE SOIL, MI
- Parts Used:
- 5304507976
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide assembly broke on left side of freezer drawer.
Took front of door off, took out freezer basket removed one screw, took off old part and put on new part, put everything back together and it was done. 15 minutes done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from NEW WINDSOR, NY
- Parts Used:
- 241779401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Broken plastic mullion hinge. Mullion was not operating correctly.
Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hampton, NH
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Previous seal had a tear and cold air was leaking around seal
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lexington, SC
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.
I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from MAGNOLIA, AR
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LEHIGH ACRES, FL
- Parts Used:
- 218755504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from WINDER, GA
- Parts Used:
- 5304508270
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.
Simple tightening of the screw with the right tool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!