66572173302 Kenmore Range - Instructions

I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!

Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.

Turned off power to range. Removed the lower panel that was secured by two screws, as well as the metal cover beneath it also secured by screws.. Removed the two screws securing the igniter, and pulled apart the black tubing that secured the igniter. (I had to pull hard to get it apart). Plug the new end into that same black tubing. screw in the two screws to secure the new igniter (this is tricky because one screw is hard to reach) I laid something in the base to cover the holes so I wouldn't lose a screw if it dropped. Screw metal panel back in, followed by the lower oven panel.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.

contracted a repair service person

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

It was very easy just two screws. The easiest thing was ordering the part. Your company had a good schematic of my appliance so it made it very easy to get the correct part.
Thank you

removed 3 screws holding the strip and replaced with new strip

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragile plastic that had broken on both sides when I replaced one inner glass piece that had broken.

Took out old one but electric hook up fell in the hole had to fish it out also dropped a screw in the hole could’ve find it used a different one

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Watch the video...

Well I had my oven door ducked taped together. I Am a 51 yr old female and I laid on the floor on my back to see if I could get the rest of the molding out without having to take off the entire oven door. I was able yo pop out the rest of the broken molding. I wasn't able to snap in the put it under the front of the oven door hold it together and screw in my new screw on the inside of the oven door. IT WORKED!! If I can do this so can you.