60462050A Frigidaire Range - Instructions

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

First unplug the stove before staring any of this task. loosen and remove three cross tip screws at the upper front of the stove top. You will need a piece of 1x3 wood about 1 1/2 feet long to hold the stove top up (sets at an angle upwards to the front). Loosen remove the bracket holding the burner you wish to replace. Disconnect the electrical wires connected to the burner. The burner is held in place with bracket clamps, remove the clamps from the oven bracket holding it. The burner will have a series if numbers in the back side, remove the brackets one at a time and reinstall on the same number on the new burner. do this to all 3 or four brackets. Install the new burner, install the bracket holding the burner, reconnect the wires. remove the wood brace and all tools. lay the stove top back down on the stove. plug the stove in and test the burner to make sure it works. turn off the burner and install the screws hold the stove to in place. Ta-Da your done. Also you tube has movie shots to give you a much better picture of what I just wrote about...

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.

2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

My husband followed the video instructions and it was easy to fix.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.