Models > 4KG25G0XWH4 > Instructions

4KG25G0XWH4 KitchenAid Mixer - Instructions

Jump to:

All Instructions for the 4KG25G0XWH4
61 - 75 of 181
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from CEDAR CREEK, TX
Parts Used:
8212396
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Russell from NEW LONDON, CT
Parts Used:
8212396
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The stand mixer would not rotate at low speed. Upon disassembly found one of the two alignment pins of the upper gear case broken.
1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from EUREKA, CA
Parts Used:
W11086780, WP9703445, WP16897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from KIRBYVILLE, TX
Parts Used:
WP9706648
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Motor knob
Watched utube
video how to repair and ordered part, easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from ST AUGUSTINE, FL
Parts Used:
W11192795, 8212396
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karl from Hammond Ranch, CA
Parts Used:
W11192795, W11086780, WP9707223, WP16897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
Planetary Pinion Gear Assembly had dropped down
The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
walter from SOUTH ELGIN, IL
Parts Used:
W11192795
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken gears
Fast
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from LILBURN, GA
Parts Used:
WP9706648
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bad speed control
Thank goodness for YouTube. Pretty much followed the process of taking it out. Was easy, but having a video made it a bit simpler.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
EBEN from WEST PALM BCH, FL
Parts Used:
WP9706648
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Madeleine from NEW YORK, NY
Parts Used:
WP9706648
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bob from ELIZABETHTOWN, KY
Parts Used:
W11192795, 8212396
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from Coeur d'alene, ID
Parts Used:
WP9706648
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
motor would surge after a few moments of running then die.
so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from PEORIA, AZ
Parts Used:
W11086780
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Stripped Gear Mixer would not mix
I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Reza from STAMFORD, CT
Parts Used:
W11192795
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROBERT from LARGO, FL
Parts Used:
WP9706885
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 4KG25G0XWH4
61 - 75 of 181