E30MC75JSS2 Electrolux Microwave Oven Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tony from Smithtown, NY
- Parts Used:
- 5304470539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave sounded like a serios short when turned on
I took off the keypad panel,then plugged it back in,turned it on for 2 seconds so I can see where the spark was comming from,saw it was the capacitor, unpluged it while it was on so the voltage would drain,took out the capacitor ordered it a few days later,put it back in, now the wife is happy,and when she is happy,I'm happy :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Waynesboro, PA
- Parts Used:
- 5304493153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Everthing works except heating.
This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDGAR, WI
- Parts Used:
- 5304504897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
sensor should pull into oven enough to easily unsnap and snap but didn't pull out
on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J from UPTON, MA
- Parts Used:
- 139001800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not spin.
Remove two screws in back to release the top.
Lift the top from the back and pull backwards to remove.
Open washer door and unscrew two screws to release the switch.
Reach down inside from the front and remove the switch.
Unplug the switch and replace with the new one. Reverse the process to install.
I found it easier to have someone hold the switch while I screwed it back in.
Lift the top from the back and pull backwards to remove.
Open washer door and unscrew two screws to release the switch.
Reach down inside from the front and remove the switch.
Unplug the switch and replace with the new one. Reverse the process to install.
I found it easier to have someone hold the switch while I screwed it back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Selma, CA
- Parts Used:
- 5304493153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Microwave Would Run And Count Down But Not Heat
Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from Depoe Bay, OR
- Parts Used:
- 5304493153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Timer runs, but no heat.
I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adam from new orleans, LA
- Parts Used:
- 5304493153
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Power, light, and clock work, micro/turntable not working
Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Cypress, TX
- Parts Used:
- 5304493153
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Instructions did not match the assembly of the ice maker.
I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Marysville, KS
- Parts Used:
- 318601604
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Oven wouldn't heat up and cook evenly.
I found the part online with a diagram of the oven with the broken part listed as a replaceable item. I ordered the part and in two days my oven was back cooking like new. Thanks
Was this instruction helpful to you?
Thank you for voting!