10689583702 Kenmore Ice Maker - Instructions

First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.

went good

My top grid was broken. After removing the old wire and loosening the screws on both ends of the old wire, I carefully unrolled the new wire so there were no kinks. Next, I put one end of the wire in a vice to hold it in place. I put a loop in the other end and attached it to the one end of the frame. You can then hold the grid in both hands and put tension on the wire as you make the wraps. When you get to the end, attach it to the grid screw and tighten the screw while maintaining tension. You can then cut the remaining wire and reinstall the grid. I think this was much easier than the directions that came with the wire. Took 5 minutes to install the wire on the grid and 15 to 20 minutes to everything back together and start making ice.

Followed instructions in Sears parts website. Not difficult but tricky to get screws out and back in.

Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got the unit back together.

stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.

Remove the cardboard back cover and the vertical metal strip, all the screws are the same on the back. Remove the front bottom cover, those screws are all the same but longer. The tubing is bad because they tucked it in on the side and it rubbed and wore a hole in it. Remove the tubing nut. You may notice that there is an insert in the tubing, but the new tubing has no insert because it is thicker walled and does not the insert because it is stronger. The nut and compression ring are one piece. Open the front door and pull the tube out of the metal plate to the left, and cut the tube off at the end to remove the metal ring, and to make it easier to pull it out. Pull the tube out from the back, but first carefully remove the sticky gray putty, and put it aside. You might also bend the copper line to the right a little if it is putting pressure on the tube at the top of the unit. Now pull the tubing out, and use it to make the new tube the proper length, You might also want to first tape the new tube to the old tube to fish it through. I did not. It was tricky fishing the tube in from the back of the unit to the resevoir. If you do it my way, then aim it to the right. I got it on the second try and felt lucky. Once you get the tube in there, put the metal ring back on the new tube, and press it into the metal plate to the right. You can feel the groove and hole in the metal plate. I think the metal ring goes under the plate, but honestly I don't think you need the ring on the new tube because it has a thicker wall and is stiffer, so it won't pop out. Make sure you put the putty back in once you have completely installed the tubing. I think this is important to keep the tubing from sweating and to help keep the ice bin cold, like insulation. Do not put the tubing back along the left side of the unit, or you will be replacing it again, but maybe not with the thicker walled tubing. When you are all done, check to make sure your sump pump works by pouring water into the ice tub, if it is plugged in and you do not hear the pump, or the water backs up, then your pump may be bad. I also pulled a piece of white plastic out of the clear tubing just above the pump and never did find where that came from, but it would have been from the ice bin. I then ran a cleaning cycle and the instructions say if there was water still in the resevoir, then do another cleaning. My resevoir was full, so I did another cleaning. IF YOUR RESEVOIR IS FULL, THEN YOU NEED A NEW UPPER PUMP! Mine is on order. Mine was full after both cleanings, and after trying to make ice, I realized what the problem was. It could be that it is very clogged, but they don't appear to be serviceable, and I never heard it try to run. I did hear the lower pump, compressor, and fan all run previously, so I hope that when the new pump is installed, the unit is not low on refrigerant or anything like that. Fingers crossed, and good luck.

The real difficulty is removing the screws. Even with a nut driver the space available makes them difficult to remove. I went to the hardware store and replaced the screws with screwdriver slots for re-installation.

I suggest following video supplied with order confirmation perfect fit

I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.

I took out old grid and removed the top broken wire. I attached the end of new wire to the terminal screw and carefully threaded the new wire back and forth without kinks. I was not able to get wire as tight as it was originally, but able to get it tight enough with pliers. I attached the other end to the opposite terminal screw. I had plenty of wire for the job and cut off the excess. I re-installed the grid and had ice the following morning. Feeling good about myself and saved a lot of money.

Found fault with recirculating pump. Found hot spot on pump circuit board . Replaced pump

Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.