1106518720 Kenmore Dryer - Instructions

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The original lint filter was broken, as the dryer was very old I did have the part #, I searched the internet I saw partselect.com on the search engin I did know it would be so easy to get this product, I selected the part by size specification.

Thank you partselect .com for making my life easy. Or else imagine me driving around looking for stores which sell spares for old dryers wasting time and gas-go green shop at home.

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

re-placed screen