66513229N411 Kenmore Dishwasher - Instructions

After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!

Snapped the new stops on. It took about 2 minutes.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

put new hose on, very easy.

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

Removed old part and replaced with new part

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.