58715363101A Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Striker
Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple.
Thank you for stocking the parts and shipping them as promised.
Thank you for stocking the parts and shipping them as promised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from St. Louis, MO
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Soap dispenser wouldn't open until the very end of the cycle
I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from HAWLEY, PA
- Parts Used:
- 5304518968, 5304517203
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm support vibrated out, melted lower spray arm.
Grab the tab on the support and rotate 1/4 turn counter-clockwise to unlock it, then lift it off. The lower spray arm simply pops off the support by spreading two tabs underneath.
Align the opening in the lower spray arm support with the outlet post in the bottom and rotate 1/4 turn clockwise to lock.
*Note: direction to remove the filter basket differed from the manual. Visually line up the notches and do not twist too far when locking or you WILL break the retainer tabs.
Simply center the lower spray arm over the support and press down until it locks into place.
Align the opening in the lower spray arm support with the outlet post in the bottom and rotate 1/4 turn clockwise to lock.
*Note: direction to remove the filter basket differed from the manual. Visually line up the notches and do not twist too far when locking or you WILL break the retainer tabs.
Simply center the lower spray arm over the support and press down until it locks into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradford from Secor, IL
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water leaked from the center of the door
DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Sandy, UT
- Parts Used:
- 154574401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
malfuction due to soap buildup and worn release
Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Benton, KY
- Parts Used:
- 154406401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher Leakibng
Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.
Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)
Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.
Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.
Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks
Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)
Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.
Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.
Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nels from Montgomery, TX
- Parts Used:
- A00099902
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher door would not latch
First I removed the six Phillips head screws that hold the control panel on. Next I removed the two Phillips screws holding the door latch in place. Then attached the new latch and reversed the procedure. Best part was the prompt delivery of the new part. My wife had herself convinced she would be without her dishwasher for several days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from OAK PARK, IL
- Parts Used:
- 5304512731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher not going through the wash cycle
First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew the control board. Put the new board in and go in reverse order until the job is complete. Good luck.
Was this instruction helpful to you?
Thank you for voting!
Water leaking from dishwasher Iwatche
I watched the partselectrepair videos for tub gasket, bottom gasket, and splash shield. The instructions were very clear and easy to follow, thank you so much now I have a dishwasher that's good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from NAPLES, FL
- Parts Used:
- A00126401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher made squealing noise during drain portion of cycle
Replaced drain pump. It helped some but still hear some squealing. I suspect the main pump might be worn as well. The drain pump did have some "looseness" to it compared to the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from New Orleans, LA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water leak underneath dishwasher
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donal from Dunwoody, GA
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washing poorly
Removed old spray arm, fitted new spray arm. VEry easy. Sorry I didn't do it months ago
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Fox River Grove, IL
- Parts Used:
- 154637401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
the valve stuck closed - no water would enter the machine
remove vanity panel
disconnect copper supply line from valve
remove valve mounting screws
rotate valve to access hose clamp
loosen clamp and slide up rubber tubing about 2 inches
pull hose off barbed fitting and remove old valve
reverse order with new valve
disconnect copper supply line from valve
remove valve mounting screws
rotate valve to access hose clamp
loosen clamp and slide up rubber tubing about 2 inches
pull hose off barbed fitting and remove old valve
reverse order with new valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Hamilton, NJ
- Parts Used:
- 809006501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking From The Bottom Of Dishwasher
Removed screws and put new bottom gasket in old one just fell out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Edison, NJ
- Parts Used:
- 5304535768, 140229954072, 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Parts required replacement.
I closed on a house a few weeks back. You really don't notice issues with appliances until your living there....the walk through doesn't give you the time to really see anything hidden. Anyway - the dishwasher had appeared to be used to wash grease covered parts from a car so I pulled all the racks and filters out and placed the order for replacement parts. I saved hundreds in obtaining replacement parts verse buying a new machine - and I didn't have to sit around waiting for a repairman to do the work for me. I've made several purchases from PartSelect, and will probably making more in the near futre - Thanks!
Was this instruction helpful to you?
Thank you for voting!