58714019409B Kenmore Dishwasher - Instructions

Only took me 5 sec, just push it in. Good as new. Thanks for the fast deliver .

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.

Pulled the broken one off, snapped the new one on.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Pulled out old gasket and shield guards and put in new ones. No tools needed. Piece of cake??

Removed the clamp holding it to the floor and
removed the c-clips holding element underneath
and put new one in. Hard part was figuring out
what was holding the element but since I still
had the schematic drawing we figured it out.
Saved a bunch on a repairman. After watching
my friend install the new element I could probably
do it myself next time.

took it out of the bag and snapped it in. Less than 10 seconds.

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

I JUST FOLLOWED THE INSTRUCTIONS . PIECE OF CAKE

Under sink: Disconnected drain hose to garbage disposal, shutoff water feed, unplugged power.
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great!

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

I just popped on a new Arm. So easy. The amazing thing was how fast I had the part and how easy it was to find on Partselect.com. I ordered the part Monday and had it Tuesday. I was stunned and the tenant was impressed.

I watched the partselectrepair videos for tub gasket, bottom gasket, and splash shield. The instructions were very clear and easy to follow, thank you so much now I have a dishwasher that's good as new.

Replaced drain pump. It helped some but still hear some squealing. I suspect the main pump might be worn as well. The drain pump did have some "looseness" to it compared to the new part.