66512779K312 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from SANFORD, NC
- Parts Used:
- WPW10538166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
I damaged the grommet when removing the recirc pump
repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet
Was this instruction helpful to you?
Thank you for voting!
The wheels broke off from the rack hangers.
The replacement kit came with no instructions in the box, so I found the instructional video online. This video pointed me in the right direction so I could take it the rest of the way myself.
Here is the link to the instructional video i used
https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm
Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.
This was a very cost effective repair instead of replacing the entire rack assembly.
NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.
Here is the link to the instructional video i used
https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm
Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.
This was a very cost effective repair instead of replacing the entire rack assembly.
NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door spring link broke.
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Rockville, MD
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap of a vertical tine in the dishwasher had come off, leaving an exposed, rusted and sharp top.
The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Beaufort, SC
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Kernersville, NC
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
old hose possible leakage
put new hose on, very easy.
Was this instruction helpful to you?
Thank you for voting!
Door spring broke-Door falls down
Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.
Was this instruction helpful to you?
Thank you for voting!
Top rack wheel broken causing rack to fall when extended too far.
watched instructions and proceeded. Parts were self evident after watch ing video. Easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DOYLESTOWN, PA
- Parts Used:
- W11175771, WPW10195536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher would not fill with water
The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from BILLINGS, MT
- Parts Used:
- W10727426
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from KENT, WA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the old stops broke
Snapped the new stops on. It took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from WESTERVILLE, OH
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
all rollers fell off. lower rack was hard to move when full
Purchase 4 roller wheel assemblies and installed them with only a screw driver to open the tangs. quick and easy and rack rolls smoothly inside the dishwasher. Rather expensive $58 per roller assembly and hopefully these last the lifetime of the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from COLLIERVILLE, TN
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
replaced wheel assemblies on lower dishwasher rack
After finally getting the older wheels off, it was literally a snap putting the new wheel assemblies on. I still don't know the best way to get the old ones off, to be honest, but putting the new ones on was really easy.
Was this instruction helpful to you?
Thank you for voting!
Kids loved to make squeaky sounds opening and closing the doors, finally snapped the door balance link on one side.
1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from HIGGINSVILLE, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Mounting bracket
Removed old part and replaced with new part
Was this instruction helpful to you?
Thank you for voting!