40205-0 General Electric Dishwasher - Instructions

Just put axle and wheel together and popped them on. Thank you. I know you saved me a bundle.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

Bottom rack - slide the old one out, slide the new one in. The rack came came with the wheels, so I didn't use the replacement ones.
Top rack - remove the rail end caps - they will likely break so order new ones. Slide the rack out. Remove the rotating spray arm and then remove all the brackets. I was able to re-use the old brackets and didn't need the replacements. Install the old brackets on the new rack, install the spray arm, and slide the new rack back into the rails. The new top rack also came with wheels installed, so I didn't use the replacement ones. Once the rack is back in the rails, install new rail end caps. Put them in sideways and facing into the washer. Straighten the caps and turn them into place. Be careful with the rail caps - they break easy and are expensive. Make sure they hold the top rack in place, and that's it.

The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Traced the problem back to the water valve. turned off the water. Disconnected the water inlet and outlet lines. removed the 2 mounting screws and unplugged the terminals.

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

Gasket it self was simple. Just pull out the old rubber gasket and "stuff" in the new one. Note the new gasket was 1-2" short, so I used a piece of the old gasket to fill in the missing length.

The "short seal" was a bit of a mystery on how to actually remove the old one. Taking off the door panel, and almost all the screws on the door did nothing to get access to the short seal. Finally, I simply pryed up the plastic door liner just enough to slide out the old seal. it has a "slot" that engages a plastic bar within the door. Putting in the new was a bit trickier, but after some three handed effort I was able to slide and then snap in the new seal.

So, in the end I really needed to remove NO screws to do the job.

After 10 washes, all seems good with NO leaks.

Bottomline, for a 4 year old dishwasher needing these parts is a bit silly. Older dishwashers I owned lasted 10-15 years with ZERO problems.

So much for GE buying all their appliances in China.......

I cut the water off to the DW, unscrewed the water connection to the inlet valve, unplugged the electric connection, disconnected the black rubber line from the valve to the washer, removed the 2 screws holding the valve in place. Put the new valve on by doing the above backwards. I also used white thread tape on any connections that needed it.

Turned spray arm while lifting upward to remove the old part. Place new spray arm over the water outlet and turned with light downward pressure until properly seated.

It less time to do the repair than it took to open the box and unwrap the part!

pulled the racks out, replaced the broken parts....easy job

Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

Hint on determining if the Main Conduit is the cause. Place a tapered flat piece of wood (wooden spatula) between the Main Conduit and rear of the dishwasher wall and remove any excess play.
Run the wash cycle and determine if the noise goes away or is reduced.

Removal and Replacement of the Main Conduit Assembly:
Opened the Dishwasher door and removed the lower and upper basket.
The upper basket required the two rubber gourmets on the front of the rail to be removed by inserting a flat bladed screwdriver between the top of white farthest tab towards the rear of the dishwasher of the rack slide end cap (PS2370502 – Item 652) and twist the screwdriver while gently pushing the top of the tab towards the rear of the dishwasher and gently pulling on the end cap (The rear tab needs to clear the upper rack slide).
Repeat this process on the other upper rack slide and remove the upper rack assembly.

Using a ¼ inch socket driver, remove the Main Conduit (PS651676 Item 585) screw located in the back of the Dishwasher wall and the screw from the upper spray arm (PS260547 Item 570) located on the roof of the unit.
Remover the lower Spray arm by gently pulling up and turning it counter clockwise.
Remove the fine filter hub nut (PS259078 item 454 ) by turning it counter clockwise and the fine filter (PS259068 item 452) The fine filter has a small tube going into the bottom of the dishwasher base that should be removed at the same time of the filter. Be sure to position it correctly when it is reassembled.
There is also a small stainless washer in the bottom of the fine filter housing. Take care not to loose it during the assembly and disassebly process

Remove the Main Conduit from the plastic assembly in the drain of the dishwasher by turning it counter clockwise. (Note, the new Main Conduit Assembly comes with this part pre assembled). Remove the same plastic piece from the new Main Conduit assembly by carefully lifting the clip on it.
Install the new piece back in the drain and tighten just prior to being pointed toward the back of the dishwasher.
Reassemble the Main Conduit to the drain piece and tighten it the remainder of the way and reassemble all parts in the reverse order they were removed.