Part Location Diagram of 5303918344 Frigidaire Rearmount Ice Maker Assembly
See part F17 in the diagram
( Grid squares measure 1x1 inch )

Rearmount Ice Maker Assembly 5303918344

Works With Model 2534433360A!

Rated by 7 customers 

?

Very Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.

?
$130.80
In Stock
Fix Number:
FIX1992700
Manufacturer #:
5303918344
Manufactured by:
Frigidaire
Works With Model 2534433360A!

Product Description

This kit includes the ice maker, power cord, bail arm, and fill cup. If your ice maker is not making or dispensing ice, or you notice a leak, you may need to replace the rear-mount ice maker assembly. This ice maker mounts to the back panel in the freezer section of the side-by-side refrigerator. If you are having an issue with the arm of this kit hitting the shelf, you will have to replace the shelf. You can find the shelf by searching FIX1152582. To complete this repair, you will need a 1/4-inch nut driver and a small flat blade screwdriver.

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 5.0 / 5.0, 7 reviews.
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Customer:
Ken from Lewisville, TX
Parts Used:
5303918344
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The ice maker wasn't producing ice.
Believe it or not, I did this in less than 5 minutes. First, clear off anything on the removable shelf covering the icemaker (in our case, four ice cube trays we had been using for a couple of months - what a first-world problem!) Remove the shelf by pulling straight out. Thurn the switch on the icemaker to "off" (toggle it to the left .) Loosen the two 1/4" hex headed bolts on the bottom of the icemaker unit. You don't have to remove them, just loosen them enough to lift the icemaker up. Once you have loosened the bolts and lifted the icemaker, undo the electrical connector behind it. Making sure the replacement unit is turned off, plug it into the connector, then put the unit back on the bolts and tighten. Get the bolts reasonably tight but don't go overboard - you don't want to strip anything! Finally, before you replace the shelf, press and hold the power button in the "on" position for at least 15 seconds. That will force the unit to go through the motions of dispensing ice, but will also then immediately fill the tray with water, which will get you the first batch of ice (which you may want to discard if there is any discoloration) in a couple of hours. Very easy!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from LANSING, MI
Parts Used:
5303918344
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Stopped Advancing Ice-Overflowing Water.
First Ice Maker had a broken bail arm hinge and water fill cup. Water fill cup was shipped attached to unit even though instructions described how to attach the fill cup to unit. Sent that unit back. Second unit shipped had a broken water fill cup also for the same reason. F*** it.....Removed the fill cup from my original unit and install ed. Still waiting for a refund on the first broken unit I sent back.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from NORCO, CA
Parts Used:
5303918344
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Ice maker still worked but leaking into freezer
Unplugged refrigerator. Removed two 1/4 inch hex heads, disconnected harness and installed new. Very easy! Was making ice in about 30 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from Parma, OH
Parts Used:
5303918344
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Rear mount ice maker would not make ice as the switch controlling the water solenoid wasn't closing.
1.Loosened the two hex head screws holding the ice maker to the rear wall with the nut driver. 2.Lifted the ice maker straight up to to where it cleared the two screws. 3.Disconnected the plug. (this was the hardest part as there is very little room for two hands to pull the plug out). 4. Connect new plug. 5.Hang Ice maker on the two scre ws. 6. tighten the two screws. It took me longer to type this out than it did to change the Ice Maker.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patricia from Fresno, CA
Parts Used:
5303918344
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The defroster to release the ice wasn't working
Turn off power and water. Loosened the 2 screws with a 1/4" nutdriver, unplugged ice maker then moved water tube out of way. installed just like it came out. Super easy! Last step make sure it looks level. then enjoy your ice!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RONNY from BARKSDALE, TX
Parts Used:
5303918344
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice Maker quit making ice.
Found replacement ice maker on your web site, by model #. Ordered replacement by model # and replaced in a matter of minutes. Received order quickly and it fit perfectly. Started making ice immediately. 1. Loosened two 1/4 in retaining screws, and disconnected old ice maker electrical connector. 2. Connected electrical connector to rep lacement and placed replacement over the two retaining screws. 3. Tightened to retaining screws. 4. Set power switch on replacement to on.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from North Richland Hills, TX
Parts Used:
5303918344
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Not making ice
Pulled out ice tray, loosened the two screws to ice maker lifted out and unplugged. Reversed the same process putting in new ice maker and was done. I have plenty of ice now.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1

Model Compatibility

This part works with the following models:
Fix Number: FIX1992700
Manufacturer Part Number: 5303918344
Brand Model Number Description
Kenmore 25344302400 Refrigerator
Kenmore 25344302401 Refrigerator
Kenmore 25344303400 Refrigerator
Kenmore 25344303401 Refrigerator
Kenmore 25344303402 Refrigerator
Kenmore 25344303403 Refrigerator
Kenmore 25344304400 Refrigerator
Kenmore 25344304401 Refrigerator
Kenmore 25344309400 Refrigerator
Kenmore 25344309401 Refrigerator
Kenmore 25344333600 Refrigerator
Kenmore 25344333601 Refrigerator
Kenmore 25344333602 Refrigerator
Kenmore 25344333603 Refrigerator
Kenmore 25344333604 Refrigerator
Kenmore 25344333605 Refrigerator
Kenmore 25344333606 Refrigerator
Kenmore 25344333607 Refrigerator
Kenmore 25344333608 Refrigerator
Kenmore 25344333609 Refrigerator
Kenmore 2534433360A Refrigerator
Kenmore 25344352400 Refrigerator
Kenmore 25344352401 Refrigerator
Kenmore 25344352403 Refrigerator
Kenmore 25344352404 Refrigerator
Kenmore 25344352405 Refrigerator
Kenmore 25344352406 Refrigerator
Kenmore 25344352407 Refrigerator
Kenmore 25344352408 Refrigerator
Kenmore 25344352409 Refrigerator