6" Heating Element WB30X44826
Works With Model 12786-1!
$158.07
In Stock
- Fix Number:
- FIX17645254
- Manufacturer #:
- WB30X44826
- Manufactured by:
- GE
Works With Model 12786-1!
Jump to:
Product Description
-
Works with the following brands:General Electric, Kenmore, Hotpoint
-
Works with the following products:Range, Cooktop, Microwave Oven Combo
-
Fixes the following symptoms:Element will not heat
-
Part# WB30X44826 replaces these:WB30K5033, WB30T10006, WB30T10047
- Works with the following brands:
- General Electric, Kenmore, Hotpoint
- Works with the following products
- Range, Cooktop, Microwave Oven Combo
- Fixes the following symptoms
- Element will not heat
- Part# WB30X44826 replaces these:
- WB30K5033, WB30T10006, WB30T10047
Part Number Cross Reference
Questions and Answers
Be the first to ask our experts a question about this part!
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts Additional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- karen from lily, KY
- Parts Used:
- 8009, WB30X44826
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
description of installing was shot on info
first of all there were four screws to take out not just 2 then since there was 1 wire more on old that had to be completely remove & disregarded that wasn't in replacement info an the fact that picture digram was upside down made connecting coded wires complicated because old burner was faceing up once you take wires off old one & ellin
... Read more
ate extra wire and not all wires were colored same had to try 4-time in changing wire slots that 4-time had to shut off breakers to electric an hope that the next time the wire config would be wright, if the had put all info about taking it apart & tuned diagram write side up there would not have been any problem changing ,should have had more instruction
Read less
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from ST AUGUSTINE, FL
- Parts Used:
- WB30X44826, WB09T10002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Haliant heating element was burned out
Turn off the power/unplug cord. Remove the two hex screws holding the cooktop to the oven/frame (you have to open the oven door to access them). Lift/tilt the cooktop up from the front and prop up with a piece of wood or something (I used a 2' ceiling fan downrod). Check the terminals on all elements with a voltmeter to ensure the power i
... Read more
s removed. You could unplug the entire cooktop (via the rear plugs and a ground wire that needs to be removed) and remove it at this point, or replace the element in the propped up position. Put a sheet or towel over the open spaces of the oven below--this will catch dropped parts. Remove the wires from their terminals on the burnt-out element. Draw or snap a picture if you need to, so that the wires are connected correctly to the new element. Remove the screws to the clips holding the element in place. Remove the element. Attach the wires to the new element per your drawing/picture. Secure the element using the clips and screws you removed earlier. Lower the cooktop. Turn on the power and test the new element. When operation is verified, secure the cooktop using the two hex screws you removed earlier.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX17645254
Manufacturer Part Number: WB30X44826
Manufacturer Part Number: WB30X44826
Brand | Model Number | Description |
---|---|---|
General Electric | 10671-1 | Range |
General Electric | 10671-2 | Range |
General Electric | 10671-3 | Range |
General Electric | 10771-1 | Range |
General Electric | 10771-2 | Range |
General Electric | 10771-3 | Range |
General Electric | 10781-1 | Range |
General Electric | 10785-1 | Range |
General Electric | 10785-2 | Range |
General Electric | 10785-3 | Range |
General Electric | 10787-1 | Range |
General Electric | 10791-1 | Range |
General Electric | 10791-2 | Range |
General Electric | 11791-2 | Range |
General Electric | 11791-3 | Range |
General Electric | 12661-1 | Range |
General Electric | 12671-1 | Range |
General Electric | 12771-1 | Range |
General Electric | 12771-2 | Range |
General Electric | 12781-1 | Range |
General Electric | 12781-2 | Range |
General Electric | 12785-1 | Range |
General Electric | 12786-1 | Range |
General Electric | 12787-1 | Range |
General Electric | 12791-1 | Range |
General Electric | 12891-1 | Range |
General Electric | 12891-2 | Range |
General Electric | 14786-1 | Range |
General Electric | 157710 | Range |
General Electric | 15781-0 | Range |
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.