Boring Machine Parts

Carbon Brush (Sold Individually)

$4.99

Fix Number: FIX10167153
Manufacturer Part Number: 176846-04

This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.

Carbon Brush and Lead

$6.39

Fix Number: FIX10183918
Manufacturer Part Number: 655213-02

This part includes one carbon brush with wire lead in attached rubber sheath. Your tool will have two carbon brushes, so it is a good idea to inspect both and replace them at the same time. This carbon brush is compatible with various types of tools, such as drills, impact drivers, and impact wrenches, to name a few. This carbon brush is sourced directly from the manufacturer, ensuring the proper fit with your equipment. It is most commonly replaced due to a poorly performing engine, and is a common wear part that should be checked regularly.

Plain Washer

$4.99

Fix Number: FIX11929226
Manufacturer Part Number: N016823

This is a genuine OEM plain washer and is part of your impact driver chuck assembly. The washer fits over the compression spring and provides a flat surface for the hog ring to sit against. This part usually needs to be replaced because it has been lost during the disassembly of the chuck. To begin this repair, remove the hog ring from the chuck, being mindful not to misplace the spring. Now you can place the compression spring in place and the new washer over top and reinstall the hog ring. Use a pair of needle nose pliers to push the compression spring as you install the hog ring over the spindle.

Watch the install video

Brush Box (Sold Individually)

$9.49

Fix Number: FIX10180814
Manufacturer Part Number: 603754-01

The brush box assembly is used on a variety of cordless tools and appliances. This assembly includes a carbon brush, spring and holder. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it disrupt the function of the motor and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions. *Please note: This part is sold individually.

Watch the install video

Belt Hook

$3.99

Fix Number: FIX10189049
Manufacturer Part Number: N268241

This OEM belt hook makes it possible for drills and drill drivers to attach to a regular belt or tool belt. It attaches to the bottom of the handle assembly and makes it convenient to access your tool when it is not in use. This part includes the belt hook and screw needed to attach it.

Watch the install video

Brush & Holder Assembly

$15.60

★★★★★

1 Review

Fix Number: FIX10187386
Manufacturer Part Number: N031214

This part contains two carbon brushes and holder sets. Carbon brushes are a routine maintenance task, as they are prone to wear due friction. Worn brushes are the most common reason for a motor that is not running properly or at all. In general, this is a pretty easy repair, but keep in mind that instructions can vary slightly depending on the model. To access the brushes, you will need to remove the housing of the tool and the brushes will be located inside the holders close to the motor.

Brush (2 Required)

$7.37

Fix Number: FIX10116574
Manufacturer Part Number: N119739

This part includes one carbon brush with a wire lead and brush spring attached. If the motor of your tool is running poorly, a common cause of this is a worn carbon brush. Carbon brushes should be inspected regularly because they are prone to wear due to friction. If you notice burning or smoke during the use of the tool, it is important to check not only the brushes, but the armature as well.