Part Location Diagram of WE4X448 GE Heat Detector
See part 552 in the diagram
( Grid squares measure 1x1 inch )

Heat Detector WE4X448

Works With Model GFD45GSMK0WW!

Rated by 3 customers 

?

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

?
$78.02
In Stock
Fix Number:
FIX268031
Manufacturer #:
WE4X448
Manufactured by:
GE
Works With Model GFD45GSMK0WW!

Product Description

Also known as Flame Sensor/Detector.

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 2.9 / 5.0, 3 reviews.
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Customer:
Joseph from New York, NY
Parts Used:
WE4X693, WE4X692, WE4X448
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Drier would heat, run but after shutting off hot. Would not reheat.
Use downloadable diagram for number reference. I opened the unit by removing the 2 screws in the front top of door on the inside near #642. Then the two back brackets #452. Took the top off. I secured the whole top unit#13 because it was unnecessary to dissemble. And you would have to open it to take apart the electrical connections. I j ust tied it up to prevent stress on the wires. I took the front off by two screws on #393 the dryer case. You can disconnect the door switch easily. Next below has an access you can reach in and apply pressure to release the tension on the belt. Make a mental note of how the belt goes on as you have to put this on again by feel. Check if its time to replace belt also. Remove belt then drum. All other parts are in good access. I changed part numbers 729,731,550. Both solenoids gave a reading on the multi-tester. I am not sure if it was the solenoids or the heat detector in this case. But changing all three did the job. According to statistics the solenoids fail often for this problem. And changing both is recommended. Your in there so might as well switch them out (Your Call). I was able to reconnect the gas and the electrical and run the dryer to check the repair with the unit open. Reassembly is just the reverse. Wear gloves there are sharp edges, don't loose screws and brackets. Order numbers are WE4X692, WE4X693,WE4X448. I am not too mechanical but once I had the unit apart it made sense to me. Also make sure to clean out accumulated lint. I found much of it inside vacuumed the inside completely.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brandon from Show Low, AZ
Parts Used:
WE4X693, WE4X692, WE4X448
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Dryer wasn't heating (or drying)
Our dryer is run 3-4 times a day (8 people in my family) so it is both essential and well used. I have done other repairs so I know my way around the inside. When the heat stopped, I did some research and found it was either the heat detector or the gas valves. As we needed to dry some clothes, I bought both. They are both located in the same area but the dryer has to be put back together to test them. I did the heat detector first. This requires removing the top panel, then front top panel, then the front and finally the side panel (Pro-Tip: when the front is removed the barrel doesn't have support. Shoving a shoe in-between the barrel and the frame will give it what it needs). Replacing the detector was simple. The wires snap on but are easy enough to just pull off. I put it back together and then it would start burning gas and not stay going. This is typical bad valve behavior, so I went back in and replaced those. Now it is drying faster than it has in years. I personally don't enjoy repair work, but I appreciate the fast shipping and accurate information on this site - it is working amazing again...
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOHN from HAVERHILL, MA
Parts Used:
WE4X448
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
dryer had no heat
large disassemble of the unit but, after reassemble worked beautifully!! correct part & quick service Thanks
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1

Model Compatibility

This part works with the following models:
Fix Number: FIX268031
Manufacturer Part Number: WE4X448
Brand Model Number Description
Kenmore 26715321 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 2671532110 Washer Dryer Combo - LAUNDRY CENTER
Kenmore 2671532211 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 2671532212 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 2671532311 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 2671532312 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 2671532412 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 2671532413 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 36371542 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 36371542211 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 36371542310 Washer Dryer Combo - HOME LAUNDRY COMBO
Kenmore 36371542410 Washer Dryer Combo - HOME LAUNDRY COMBO
General Electric 36371542411 Washer Dryer Combo - GE Home Laundry Combo
General Electric 63740118 Dryer
General Electric 63740119 Dryer
General Electric 64100119 Dryer
General Electric 64100129 Dryer
General Electric 64100139 Dryer
General Electric 64100149 Dryer
General Electric 64100159 Dryer
General Electric 64100169 Dryer
General Electric 64100179 Dryer
Whirlpool CADG265RAL Dryer - Whirlpool Dryer Cadg265ral
Whirlpool CADG265RBL Dryer - Whirlpool Dryer Cadg265rbl
General Electric CADG265RCL Dryer - GE Dryer Model CADG265RCL Parts
General Electric CGL2000R*119 Dryer
General Electric CGL2000R*178 Dryer
General Electric CGL2000R*179 Dryer
General Electric CGL2000RW169 Dryer
General Electric CGL3000R*178 Dryer