Part Location Diagram of WE12X10014 GE Dryer Belt
See part 213 in the diagram
( Grid squares measure 1x1 inch )

Dryer Belt WE12X10014

Works With Model 62188419!

Rated by 4 customers 

?

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

?
$31.77
In Stock
Fix Number:
FIX2350043
Manufacturer #:
WE12X10014
Manufactured by:
GE
Works With Model 62188419!

Product Description

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.0 / 5.0, 4 reviews.
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Customer:
John from West Elkton, OH
Parts Used:
WE12X10014
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Replacing belt
First watched some you tube videos, to see how to get dryer apart, the one issue I had was getting the belt onto pulley etc. I found if I removed small access panel in back it was a lot easier than trying to reach in from the front as shown in most of the online videos
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Maryland Heights, MO
Parts Used:
WE12X10014
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
belt broke after 38 years
Removed vent pipe pulled it away from the wall. Unplugged it,and ground wire. Opened top and loosened front.installed new belt and figured out tensioner worked (that took time!) and picked up broken belt. Put back together.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Gravois Mills, MO
Parts Used:
WE12X10014, WE25X60
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Drive belt broke after 24 years of service
Disconnect power. Removed four screws from the top of the door opening. These screws have a star pattern and require a star type screw driver. With the four screws removed, lift the front edge of the top and rotate it upward to a vertical position for access to the drum. Locate and remove two screws located at the inside top corners secur ing the front panel. Disconnect two door switch wires. Loosen, but don't remove the two screws at the front bottom corners of the machine that secure the bottom of the front panel. Lift the front panel up about an inch and rotate the front panel 90 degrees to the right. Using a vacuum, start vacuuming accumulated lint and dirt. Lift the dyer drum up slightly and pull forward. Vacuum and set aside. Vacuum lint and dirt from dryer housing. At the back of the dryer, remove the dryer duct and remove the black panel at the bottom of the housing. Check drum slides at the front of the machine and replace if damaged or worn. Reinstall the dryer drum, draping the new drive belt around the drum prior to engaging the bearing pin at the rear. From the opening at the bottom rear of the machine, tread the drive belt around the motor drive pulley and the tensioner wheel. The portion of the drive belt coming from the left side of the drum (as seen from the rear) must engage the right side of the tensioner wheel before going around the motor drive pulley. This will provide proper drive tension. Re install rear cover and re install the dryer exhaust duct. From the front, re install the front panel and install the two top screws. Then tighten the two bottom screws that were left loose. Re connect the door switch wires. Lower the top and install the four screws at the top of the door opening. Test the dryer operation.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from Sandyston, NJ
Parts Used:
WE12X10014
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
brocken drum belt
great
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1

Model Compatibility

This part works with the following models:
Fix Number: FIX2350043
Manufacturer Part Number: WE12X10014
Brand Model Number Description
Kenmore 363DDE8509RCMA Dryer - Kenmore Dryer Model 363.DDE8509RCMA (363DDE8509RCMA, 363 DDE8509RCMA) Parts
Kenmore 363DDE8509RCMW Dryer - Kenmore Dryer Model 363.DDE8509RCMW (363DDE8509RCMW, 363 DDE8509RCMW) Parts
Kenmore 363DDE9600RCMA Dryer - Kenmore Dryer Model 363.DDE9600RCMA (363DDE9600RCMA, 363 DDE9600RCMA) Parts
General Electric 61140418 Dryer
General Electric 61140419 Dryer
General Electric 61148418 Dryer
General Electric 61148419 Dryer
General Electric 62140418 Dryer
General Electric 62140419 Dryer
General Electric 62148418 Dryer
General Electric 62148419 Dryer
General Electric 62170419 Dryer
General Electric 62180419 Dryer
General Electric 62188419 Dryer
General Electric 62190419 Dryer
General Electric 62190429 Dryer
General Electric 62190439 Dryer
General Electric 62190449 Dryer
General Electric 62190459 Dryer
General Electric 62190479 Dryer
General Electric 62198419 Dryer
General Electric 62198429 Dryer
General Electric 62198439 Dryer
General Electric 62198449 Dryer
General Electric 62198459 Dryer
General Electric 62198479 Dryer
General Electric 63040419 Dryer
General Electric 63040459 Dryer
General Electric 63040479 Dryer
General Electric 63048419 Dryer