LG Washer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
LG Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular LG Washer Parts

Watch the install video
Washing Machine Drain Pump – Part Number: 4681EA2001T
Washing Machine Drain Pump
$74.04
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX3579318
Manufacturer Part Number
4681EA2001T
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it can cause the washer to not drain properly. Keep in mind that the pump casing is sold separately. This repair is rated medium-difficulty and can vary depending on the model. For this repair you will need a Philips screwdriver, a small flat blade screwdriver, needle nose pliers, and slip joint pliers. Do not forget to disconnect the power before you begin this repair. In general, this repair can be started by removing the top of the washer followed by the front panel. Moving down the front of the appliance, remove the door, latch, tub gasket, and drainer cover. The drain hoses and clip will need to be disconnected from under the drain assembly. To install the new pump motor, reassemble parts in the reverse order. We recommend taking photos while disassembling and keeping screws and parts neatly organized.
Fixes these symptoms
  • Draining Issues
  • Engine runs but does not pump water
  • Leaking
  • See more...

Installation Instructions

Michael from Oconomowoc, WI
Water was not draining from wash tub. A code "0E" was showing on the display
Your Youtube video describes the repair perfectly. I'll add: Be careful when removing and placing the control panel on top of the Washer. Once removed, my panel had a wire harness with a zip tied. I cut the zip tie to allow enough slack to lay the panel on top of the washer. No need to disconnect any wires (I put a new zip tie on upon reassembly.) Be careful when removing the retention ring around the Rubber Boot, takes a little finesse, but not too difficult, Don't use a sharp object as you don't want to cut the boot. Make sure the boot is properly seated and the retention ring is securely in place upon reassembly. When removing the old pump my model has the pump held in place with 2x screws (easy to get at from the front) and also slides onto a plastic foot that has a "tab" that needs to be depressed to slide the motor out. You can't see the foot or tab from the front of the washer, as its hidden behind the pump, but fish around with your hand and you'll feel the tab..hold it down and the pump will slide towards the back of the Washer. Thanks, $60 bucks and couple hours was way better than a new $700 Washer. Read more...
Watch the install video
Dryer Lint Filter – Part Number: 5231EL1003B
Dryer Lint Filter
$50.03
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX3527578
Manufacturer Part Number
5231EL1003B
If the lint filter in your dryer has become damaged, this is a genuine OEM replacement filter. It is important to always run the dryer with the filter in place, as it traps lint and other debris from entering the dryer vents. Without the filter, the vents can become clogged with lint which can prevent your laundry from drying properly along with being a fire hazard. Replacing this part is an easy repair. Simply remove the old filter, and insert the new one in its place. Always be sure to clean the filter between each load of laundry.

Installation Instructions

Jeanne from Cincinnati, OH
Needed new lint filter.
Take out the old filter and slip in the new filter. Read more...
Magnetic Door Plunger – Part Number: AGM73610701
Magnetic Door Plunger
$24.21
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX3618292
Manufacturer Part Number
AGM73610701
The magnetic door plunger is used on your washing machine to keep the door open when not in use. This allows for the inner door and tub seal to dry thoroughly, which helps to prevent any buildup of mold or mildew. If your washer door is not closing properly, the magnetic door plunger may be damaged and needs to be replaced. This genuine OEM part includes the plastic housing and a spring. To install the part, you just need to line up the tabs on the plunger with the slots on the inner door panel and snap it into place.
Fixes these symptoms
  • Leaking
  • Lid or door won’t close
  • Locking Issues
  • See more...

Installation Instructions

DEREK from Fishers, IN
Plunger was broken
Very simple fix, line clips with door and push in. Read more...
Watch the install video
Water Inlet Valve - Hot – Part Number: 5220FR2006H
Water Inlet Valve - Hot
$26.77
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX3527427
Manufacturer Part Number
5220FR2006H
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with water at all. If this happens the valve should be replaced. There are a couple different methods for testing if your hot water valve is defective. The first is to use a multimeter on the solenoid, the second is to unplug the washer while it is running. If water continues to flow into the machine, then the valve is defective. This genuine OEM part has a standard hose fitting inlet, one water outlet, and measure approximately 3 inches long by 3 inches wide. To complete this repair, you will need to disconnect the water and power supply to your washer and pull it out from the wall so you can access the back panel.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...

Installation Instructions

Frederick from Kennesaw, GA
Washer was leaking at the bottom
I actually looked on you tube for the type of washer and the issue. I checked all the areas the various videos showed me. The last one I checked was the inlet valves. All that is needed is a Phillips head and a wrench. Took the top off. Unplugged the washer. Unplugged the hoses. Unscrewed the valves and removed the hoses and the circuit pieces. Replaced one at a time. Everything worked perfect. Hooked hoses back up. No more leaks. Attached the top back and pushed back into place. No more leaking. Read more...
SENSOR ASSEMBLY – Part Number: 6501KW2002B
SENSOR ASSEMBLY
$41.76
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX16556422
Manufacturer Part Number
6501KW2002B
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
Fixes these symptoms
  • Spinning Issues
  • Spins slowly
  • Will not agitate
  • See more...

Installation Instructions

John from LAKE GROVE, NY
pump was blow and the sensor broke
My friend is a handy man and did everything for me but i will definitely use you again. Read more...
Watch the install video
Water Inlet Valve - Cold – Part Number: 5220FR2075L
Water Inlet Valve - Cold
$72.84
In Stock
Fix Number
FIX11728995
Manufacturer Part Number
5220FR2075L
If your washing machine is leaking, slow to fill, will not stop filling with water, or is not filling at all, the cold-water inlet valve may be defective. The purpose of the valve is to open to allow water into the washer, and is used for cold water, liquid bleach, and prewash cycles in your washing machine. This is a genuine OEM replacement part that measures approximately 4 inches long and 3 inches wide. It has a standard hose fitting inlet along with two outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left. When replacing this part, you will want to disconnect the power and water to your washer and remove the fill hoses. You will need to pull the machine out far enough so that you are able to access the back panel where the valves are located.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...

Installation Instructions

Frederick from Kennesaw, GA
Washer was leaking at the bottom
I actually looked on you tube for the type of washer and the issue. I checked all the areas the various videos showed me. The last one I checked was the inlet valves. All that is needed is a Phillips head and a wrench. Took the top off. Unplugged the washer. Unplugged the hoses. Unscrewed the valves and removed the hoses and the circuit pieces. Replaced one at a time. Everything worked perfect. Hooked hoses back up. No more leaks. Attached the top back and pushed back into place. No more leaking. Read more...
Washer Water Inlet Valve – Part Number: AJU75152601
Washer Water Inlet Valve
$126.12
In Stock
Fix Number
FIX12374721
Manufacturer Part Number
AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...

Installation Instructions

Joy from HALIFAX, PA
My washer would not stop filling with water even when turned off
Unplugged it. Took back panel off. Unscrewed valve cover. Unhooked hoses. Replaced inlet valve. Replaced hoses. Replaced cover. Replaced panel Read more...
Door Boot Seal – Part Number: MDS47123602
Door Boot Seal
$116.56
In Stock
Fix Number
FIX3535210
Manufacturer Part Number
MDS47123602
This door boot is for washers. Door boot forms a seal between the wash tub and the door, preventing leaks. Unplug the washer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Watch the install video
Door Lock Assembly – Part Number: EBF49827801
Door Lock Assembly
$85.57
In Stock
Fix Number
FIX3533609
Manufacturer Part Number
EBF49827801
The door lock assembly is a genuine OEM part for your washing machine. This part informs the washer that the door is closed and locked in place, which allows the machine to start its cycle. If you are not able to open or close the door, or the washer will not start, the door lock assembly may need to be replaced. This can happen if the switch has shorted out, which will prevent the latch from locking. Before beginning this repair, please be sure to disconnect the power supply to your washer. You will need a Phillips screwdriver in order to replace this part.
Fixes these symptoms
  • Lid or door won’t close
  • Locking Issues
  • Will Not Start
  • See more...

Installation Instructions

Edward from St Augustine, FL
Door Latch malfunction
I basically followed the video instructions which made it very easy to understand and follow. The most difficult aspect was disconnection the wire harness in a small space. Read more...
GASKET – Part Number: MDS66290801
GASKET
$126.90
In Stock
Fix Number
FIX12590532
Manufacturer Part Number
MDS66290801
Fixes these symptoms

LG Washer Appliance Types

Related LG Washer Parts

Popular LG Washer Models

View More
+