Gibson Washer Parts

Gibson Appliance Parts

Popular Gibson Washer Parts

Door Strike
$13.75
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX890617
Manufacturer Part Number
131763310
Located on the door of front load washing machines, the Door Strike ensures that the door will lock by activating the switch, which in turn allows the appliance to run properly. If your washer door will not open or close, is leaking, or the machine will not start or spin, your door strike may be damaged and should be replaced. Regular wear and tear, or a misaligned door may cause the piece to break. This is an easy repair and requires a Phillips screwdriver. This genuine OEM part is made of white plastic, approximately 2 inches in length, and is held in place by 2 screws on the inside of the door. Simply unscrew and remove the old part, line up the placement of the new part using the notch, and tighten the screws back into place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Howard from Santa Rosa, CA
door ajar alarm
myself and it was easy , as the diy video described on your website Read more...
Shock Absorber Kit
$39.64
In Stock
Fix Number
FIX3508101
Manufacturer Part Number
5304485917
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
Fixes these symptoms

Installation Instructions

JOSEPH from Olympia, WA
Two busted shock absorbers
The tight confines put a hammer out of the question, so I used needle nose pliers to work the pins out (using leverage against sections in the washer) and then bar clamps to force the new pins in. Bar clamps were critical to the successful installation of these pins given the lack of room I had to work with. Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX12364048
Manufacturer Part Number
131763256
This door lock and switch assembly is an authentic OEM replacement part for your front load washing machine. The lock is used to prevent the door from opening while the machine is running, and the switch indicates that the door is closed, allowing the washer to begin its wash cycle. Attempting to open the washer door while it is still locked can cause damage to these parts. If your washer door will not open, close, or lock, you may need to replace the lock and switch. Please be sure to disconnect the power supply to your washer before beginning this repair.
Fixes these symptoms
  • Leaking
  • Lid or door won’t close
  • Locking Issues
  • See more...

Installation Instructions

Arthur from New Castle, DE
Door would not close/latch.
Removed door from washer. With door on flat surface all the screws are easily removed to replace striker & door hinge/ bushings. Pay attention to bushings position when removing so as to replace them in the same position. Video shows a guy pulling the door gasket off to replace the door lock & switch assembly. Skip that & remove the top cover from the washer. Only two screws in the back hold it on & it's a lot easier to reach inside & pull the switch up than fighting with the door gasket. With the new door hinge, door closes easier & more solid than when brand new. Easy fix. Read more...
Drive V-Belt
$24.91
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX1146950
Manufacturer Part Number
134511600
If your washer drum is not spinning, there may be an issue with your drive belt. The drive belt wraps around the motor pulley and helps the basket to spin. Other signs there are issues with the belt is if there is a burning rubber smell, or the washer is noisy while spinning. The belt is subjected to wear and tear, and over time it may wear out. This is a genuine OEM part that is made of rubber.
Fixes these symptoms

Installation Instructions

michael from Cave City, KY
browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple Read more...
Fix Number
FIX7783938
Manufacturer Part Number
137221600
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
Fixes these symptoms

Installation Instructions

Merle from St.Joe, IN
Washer wouldn't drain
Replaced the drain pump Read more...
Fix Number
FIX419285
Manufacturer Part Number
134051000
This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are not spinning, your washer is not agitating, or you are noticing excess noise and/or a burning smell. This belt is black with six ribbings. To replace this part, you will need a Phillips screwdriver.
Fixes these symptoms
  • Burning smell
  • Spins slowly
  • Will not agitate
  • See more...

Installation Instructions

Phyllis from Brownville, NY
belt was worn and stretched
Place belt on the motor first. Then place belt on pulley on the left side and turn pulley clockwise. Hold belt tight and rotate clockwise. Be careful not to pinch your fingers. Before you buy a belt check your tub first. Grab it in the inside of the front of the tub. If it moves more than a little up and down like an inch or two your tub is shot or the bearings are gone. Found that out later. Check tub first than decide what to do. Read more...
Fix Number
FIX2342445
Manufacturer Part Number
137108000
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Fixes these symptoms

Installation Instructions

Charles from BELLINGHAM, WA
washer wasn't draining
disconnected front pan and un hooked electric Read more...
Fix Number
FIX735645
Manufacturer Part Number
134144700
Fixes these symptoms

Installation Instructions

Michael from sacramento, CA
wash tub hanging low horrible noise while washer was running
one spring was broken and one shock was broken. I used a ratchet strap slung under the tub to raise it enough to install the new springs and used a 1/2" drive socket on the drive end to slip over and release the plastic pins to remove the shocks. pretty easy except that it is all done laying on the floor. I pretty much followed the instructions I found on line. I had to remove lower front panel, rear panel, and top panel to access all this. Also unplug and remove control box. Read more...
Single Shock Mounting Pin
$23.44
In Stock
Fix Number
FIX417323
Manufacturer Part Number
131268300
Dual Action Agitator
$133.53
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX418275
Manufacturer Part Number
131605901
Fixes these symptoms

Installation Instructions

Phillip from Mount pleasant, SC
Agitator loose and rattling, clothes not getting clean
1) unplug washing machine 2) remove fabric softener cup lid by pulling straight up 3) remove fabric softener cup 4) remove agitator nut seal by grasping tab with ppliers and pulling straight up 5) remove nut then pull dual action agitator straight up. 6) install new dual action agitator by pushing straight down 7) reinstall nut 8) reinstall nut seal 9) reinstall fabric softener cup 10) reinstall fabric softener cup lid 11) plug washing machine back in to outlet 12) wash clothes...done. Read more...

Gibson Washer Appliance Types

Related Gibson Washer Parts

Popular Gibson Washer Models