Models
>
GFWH1200H0WW
GFWH1200H0WW General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GFWH1200H0WW
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
This is the replacement water valve for your washer. It has 2 inlets and 3 outlets. The water valve connects to the water source and solenoid wires, and ensures the tub has the right amount of water e...
In Stock
Order within the next 8 hrs and your part ships today!
$76.86
Keep your washer running smoothly with this replacement shock absorber. It helps reduce vibration and keeps the drum steady during cycles—especially when spinning at high speeds. If your washer is mak...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
$130.88
The door lock prevents the washer door from opening during the wash cycle or spin cycle.
In Stock
Order within the next 8 hrs and your part ships today!
Special Order
In Stock
Order within the next 8 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GFWH1200H0WW
Viewing 5 of 5Leaking
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Miguel from Jacksonville, FL
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The washer stop and blinks in the RINSE MODE
I called a repair person to check my 15 months old GE front loader washer that stopped in rinse mode. After his inspection he said it was a deffected computer board and it would be very expensive to replace the 3 computers boards inside and it would be cheaper to buy a new top loader washer. The next day I lifted the top cover and foun
... Read more
d a taped plastic envelope with instructions titled “For service Technicians Only." On page 2, instruction on to how to enter the washer in to service mode and to test the washer:
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Houston, TX
- Parts Used:
- WH13X10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stops at rise
removed 5 screws, unscrew two more screws, remove the houses and disconnect the wires remove the watter valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from SEBASTIAN, FL
- Parts Used:
- WH01X20826
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Damper-Shocks Brocken-Arrowhead top broken off all four (4) Dampers
~Unplugged
~Removed front bottom and rear center panel
~Removed broken dampers. Varying difficulty; other components in the way. Used socket to help push pin out with screwdriver and pliers to help remove the pin.
~Installed New Dampers: Used Small (6") crescent wrench for top. Fitting two (2) hands in there, one to h ... Read more old and one to turn was a challenge for all four (4) dampers. Had to extend a couple to wedge to damper in there to hold the arrow hear flush.
Installing the pins in the bottom was somewhat easier than the top. I broke the retaining pin completely off an old pin to align the new damper to the base mounting hole (hard to see in there). Used Pliers, a long screwdriver and rubber mallet.
Note my situation was in a very small room. So small I had to remove the door to the room so that I could pull the washer out to get behind it. The warnings about sharp edges should not be ignored! Long sleeves (chainmail) and steel fish fillet gloves might help!
~Removed front bottom and rear center panel
~Removed broken dampers. Varying difficulty; other components in the way. Used socket to help push pin out with screwdriver and pliers to help remove the pin.
~Installed New Dampers: Used Small (6") crescent wrench for top. Fitting two (2) hands in there, one to h ... Read more old and one to turn was a challenge for all four (4) dampers. Had to extend a couple to wedge to damper in there to hold the arrow hear flush.
Installing the pins in the bottom was somewhat easier than the top. I broke the retaining pin completely off an old pin to align the new damper to the base mounting hole (hard to see in there). Used Pliers, a long screwdriver and rubber mallet.
Note my situation was in a very small room. So small I had to remove the door to the room so that I could pull the washer out to get behind it. The warnings about sharp edges should not be ignored! Long sleeves (chainmail) and steel fish fillet gloves might help!
Read less
Was this instruction helpful to you?
Thank you for voting!