Located on the door of front load washing machines, the Door Strike ensures that the door will lock by activating the switch, which in turn allows the appliance to run properly. If your washer door wi...
In Stock
Order within the next 6 hrs and your part ships today!
This door lock and switch assembly is an authentic OEM replacement part for your front load washing machine. The lock is used to prevent the door from opening while the machine is running, and the swi...
In Stock
Order within the next 6 hrs and your part ships today!
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
In Stock
Order within the next 6 hrs and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
In Stock
Order within the next 6 hrs and your part ships today!
This screw-in plastic leveling leg supports the washing machine. If your washer loses balance while it is tumbling, or makes loud noises, then it is best to replace the leveling leg to make sure the h...
In Stock
Order within the next 6 hrs and your part ships today!
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
In Stock
Order within the next 6 hrs and your part ships today!
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Order within the next 6 hrs and your part ships today!
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carl
March 13, 2023
E90 code
For model number ATF6000ES1
Hi Carl, thank you for the question. E90 error means that your main central control board and the motor control board are not communicating with one another properly. Faulty wiring could be the cause of your washer showing the E90 error code. This faulty wiring could be due to unprofessional repairs that led to disconnections or moving and relocating disturbances. When wires come loose, there is a chance of not only short-circuiting but also of sending the wrong signals. These connections involve several dozen wires linked to the central control unit. They require proper testing and examination to determine which might be causing the problem and what needs to be repaired. If the wiring is fine, then you may need to check the main central control board, part number FIX1152359, and the motor control board, part number FIX1524621. If any of the boards is faulty, you may need to replace them. We hope this helps!
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. The
... Read moren along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.