79032623311 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Colin from MORGANTOWN, WV
- Parts Used:
- 808608802
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Stove pilot not clicking on any burner, oven works fine
Unplug the range. Remove screw to Take of the back panel on upper right corner. Unclip the old spark module, unplug the wires with the needle nose pliers and plug them into the new spark module same as the old module. Clip it on. Replace the back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Brunswick, GA
- Parts Used:
- 316445501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven light stayed on & smelled like electrical burning.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from PITTSFIELD, MA
- Parts Used:
- 5304504202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Meat Probe insulation separated on the probe end
I searched the web for a replacement and Parts Select had a picture and part number for the exact same probe. I ordered the probe and it arrived very quickly. The problem was that the probe I received didn't match the picture as shown on the web site. Instead I received a probe that was a different color and the actual probe was about 2" shorter than the one I was replacing. I called customer service and was told that the probe I received was the new version that the older version was discontinued. If they had updated their pictures on the web site I would not have ordered the probe. Parts Select customer service did apologize for the issue and offered to have me return for a refund.
I will order from Parts Select but I will call first to verify that the item pictured is the actual item being shipped. Parts Select please update the part pictures to show the actual items being sold.
I will order from Parts Select but I will call first to verify that the item pictured is the actual item being shipped. Parts Select please update the part pictures to show the actual items being sold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hans from JERUSALEM, AR
- Parts Used:
- 316031501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Replace oven gas safety valve.
It went really well until test when the flame was reaching up into the oven itself, not good. Much research finally found an older repairman who informed me the nozzle that injects the gas into the oven burner had to be fully screwed down for LP Gas. The unit is pre-set for Natural Gas. Tightened it all the way down and everything works just fine. We live rurally so use Liquid Propane Gas, not Natural Gas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MERCERVILLE, NJ
- Parts Used:
- 5303935059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter failing to energize even though there was 120 volts being supplied.
Slide Range away from wall, unplug Range, remove rear cover (4) screws, removed burner assembly (5) screws, unplugged Igniter connector, loosen Igniter bracket, remove Igniter (2) screws. Reverse process to install new Igniter. I also wore latex gloves to prevent touching graphite portion of Igniter. Tested Broiler for operation, slid Range back into position. All good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from NORWOOD, PA
- Parts Used:
- 5303935059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replace igniter
New part needed to be spliced to old connector with porcelain wire nuts then removed lower oven drawer to access the connection for igniter
Was this instruction helpful to you?
Thank you for voting!