JGRP536WP02 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Ranchos de Taos, NM
- Parts Used:
- WPW10475147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burners kept clicking after ignited
This problem was driving me crazy for months. Of course, after I bought and installed the part and it still was not fixed I finally found a website that told me how to fix the clicking. The problem is that the removable head burners (#8 on the top assembly diagram) are not making good electrical contact with the base burners (#22). What I did was grab the head burners and grind them back and forth into the base burners with the weight on the heal of my hand. Steel wool or sandpaper would work too--you just want to clean the surfaces to restore electrical contact.
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one.
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Seattle, WA
- Parts Used:
- WP9755542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
faulty meat probe
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from NEW JOHSONVLE, TN
- Parts Used:
- WPW10169757
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace KitchenAid oven light bulbs
Pull the end of the lens nearest the oven door out of the oven wall. Because our oven is several years old and the bulbs had not been previously changed, I could not pull the lens out with my hand, so used two small screwdriver under the metal tabs which hold the lens in place, the metal holder came out with the lens. Once the lens is removed, simply pull out the old bulb and, either while wearing surgical gloves or holding the bulb with a cloth (do NOT allow bare skin to touch the bulb or you will be replacing it again sooner rather than later), push the new bulb's pins into the socket. The lens then is simply pushed back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from BUFFALO, NY
- Parts Used:
- WPW10131825
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bUILT IN OVEN NOT COMING UP TO TEMPERATURE
Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and connector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from White Rock, NM
- Parts Used:
- WPW10475147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the spark igniters would continue to spark after the burners were lit
Since the problem would only occur when the right front burner was on, I first replaced the ignitor, but the problem persisted. To replace the spark module I had to pull the range out of the nook it is in in the counter top. Then (after ensuring that the power was off) I removed the back cover. The spark module was easily located and removing two screws and disconnecting a few wires liberated it. The new one went in easily since it is the same part number and an exact match. Put the back on and check that the problem was solved. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from St Louis, MO
- Parts Used:
- WPW10475147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
One burner would continually keep sparking after burner ignited
Removed the small access cover on the bottom of the cooktop by reaching inside and under the cabinets. Removed the module which was held by two hex head screws, unplugged the wires noting the location and color of the wires. Plugged the wires into the new module in the proper locations as noted previously. Attached the module with two screws, and then attached the cover/access plate with two screws. Problem resolved, repair was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from JOHNSTOWN, CO
- Parts Used:
- 8186321
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Too Small
Your website says these are the replacement rubber tips for the grates on the range. They arrive and they are too small and fall out. I spoke to the "chat" on your website. I am informed they do not sell the rubber tips separately. You have to purchase a new set of grates for $294. Ridiculous. Why sells rubber tips for grates that don't fit the existing grates. I wasted $24 in purchasing the grates which included $9.99 shipping and $5.40 shipping to return the item.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from MOUNT VERNON, WA
- Parts Used:
- WPW10475147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ignitors wouldn’t stop clicking when using front right burner
Installed new spark module by removing back panel of stove. Removed two screws holding old module. Disconnect lines, marking colors. Installed new. Problem not solved. Out $128 since new module was not returnable after install.
Called Judd and Black service department. Tech came on service call. Said it was bad gas valve. They ordered part. Than needed two weeks to install. I installed it and problem persisted. Could not return part because I installed it myself. Out $180. I had cleaned ignitor with alcohol from top. Took apart cooktop and cleaned from bottom. Problem fixed for free. Out over $500 in parts and labor.
Called Judd and Black service department. Tech came on service call. Said it was bad gas valve. They ordered part. Than needed two weeks to install. I installed it and problem persisted. Could not return part because I installed it myself. Out $180. I had cleaned ignitor with alcohol from top. Took apart cooktop and cleaned from bottom. Problem fixed for free. Out over $500 in parts and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from TINLEY PARK, IL
- Parts Used:
- WPW10131825
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven will not maintain set temp
Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from EVANSTON, WY
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven temperature did match target temp entered on control panel.
I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.
Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURIE from BILTMORE LAKE, NC
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The oven was over heating because it wasn’t reading the temperature
Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Canyon Country, CA
- Parts Used:
- WP9755542
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb inop
Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Massey, MD
- Parts Used:
- WP9755542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken meat probe
My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ned from leland, MS
- Parts Used:
- WPW10475147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
would not light
remove two screws then unplug the wires put the wires back on the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from rochester, NY
- Parts Used:
- WP9755542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The oven shipped without a temperature probe.
Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.
Was this instruction helpful to you?
Thank you for voting!