UMV1170LS03 Whirlpool Microwave - Instructions

My unit is a wall mount/cabinet/built-in model. The repair is actually fairly simple once you determine that the actual microwave is just a component of the entire unit, and that it (the microwave) can be easily removed from the unit. I did not figure this out until after I removed the entire unit (disconnect the power supply, lift the entire bulky, heavy unit out of the cramped space in the cabinet, etc). Once I got it out I figured out how easy it is to remove the actual oven - a couple of screws, literally. The unit is a bit bulky, but not particularly heavy and is quite manageable. I did this entire process alone.

I got the oven out, rolled it on it's side and found the plate to access the motor. The plate is located on the bottom/underside of the unit. The plate is nothing more than a section of the underside of the metal housing that has been cut-out as an access point. This "cut-out" is not complete - that is, not completely cut out so as to all the plate to stay in place without the need for screws, etc, until you actually have to use it. I used a pair of dykes to cut the couple of points still connecting this plate, removed the two phillips screws to remove the motor, disconnected the two wires connected, then reversed to complete the repair. You then flip the cut-out plate over/rotate it, and some screw holes line up. Find a couple of small screws, and re-attach the plate to cover the motor.

The actual fix is really easy, again, once you figure out the simple way to remove the oven. I am an idiot, so you will probably find this much easier. I could probably do this repair now, after my experience, in less than 30 minutes (probably less than 15 minutes). I probably save a couple hundred $ by doing it myself so was well worth the time to do it. Good luck.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

I measured. I leveled. I mounted hanging bracket and here's where it got tricky because you need two people to raise the microwave into position. I'd stack 2x4's In the back by the wall. I'd stackem in the front on the cabinet top then raise the back and add more. You get it front back front back until it's high enough to snag the bracket. Holes pre drilled raise it on up tighten bolts and poof you're done!! I did loosen the screws that pull the cabinets together and the bottom screw that holes the cabinet on one side. It didn't seem like it needed it the way it slipped in but maybe it slipped in because I did it. Only takes a minute. Use a minute here save an hour there. Go do it! Times a wastin!!

mounted bracket, case closed.

Two Mounting plates # PS12074431 were sent to me and both do not fit.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.

I had the help of a handyman, I'm 75 years young but not handy with tools

I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.

Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.

Overall a very simple repair.

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.

took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.