63013023010 Kenmore Dishwasher - Instructions

pushed with thumb pressure and snapped rollers into place.....EASY

replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.

Replacement was fast and very simple. Was completed in less than 5 minutes.

There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.

I watch utube to assess the problem then took eveything apart and saw the build up on the filter, which i had never cleaned. I tried to clean it but was unsuccessful so order the filter from partselect and it came within a couple of days, installed very easily and began to clean as it always had.

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

This is a piece of cake. No tools are actually needed. Grasp one end of the old seal and gently pull it out of the groove in which is fits. Take the new seal, and paying attention to which way around it fits (there is a right and wrong way!) start at either end. Leave an inch or so beyond the groove to rest on the bottom of the dishwasher, and press the seal in place in the groove. You should have an inch or so left at the far end. Go back and go all along the seal and make sure it is pressed evenly and completely into the groove the full length.

You're done.

easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet

I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.

The repair was extremely simple. Just lined up and popped them on. No tools needed.

when you receive the drain pump and you are ready to install make sure you put VASELINE around the rubber Gromit that will make putting the drain pump in very easy, also to give yourself more space to remove and install the pump remove the front door panel.
It took me 20 minutes from start to finish

My Bosch dishwasher is approx 11 years old. It was leaving water in the dishwasher pan at end of the cycle.

I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have difficulty getting it to come loose.

On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.

Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.

Tried the door lock first. Did not fix the problem.

Replaced the drain pump and it fixed the problem.

Parts Select identified the pump as the most frequent problem.

Next time I will order both parts when one is cheap for any repair.

Find Parts Select is very helpful. They have identified a problem with a washing machine in the past.

I will use them for future problems.

Removed old discharge pump and replaced it with the new one. After four attempts the dishwasher worked once. This cycle continued for the next 3 attempts then it stoped all together. Ordered the sensor, installed it snd the dishwasher still doesn’t work! Now what do I do???

Followed instructions from YouTube.