1032-005A Frigidaire Dishwasher - Instructions

First I noticed that the old gasket had disintergrated along the bottom. Next I removed the the gasket being careful to observe how it was installed. There are these notched areas of the gasket that belong in the lower corners. I think the notches are designed to help hold the gasket in place and make the gasket bend around the corner. The gasket made closing the door very hard at first but after one wash cycle the fit became much more comfortable. The heat probably made the gasket more pliable. Problem solved.

My door spring had broken and I was going to leave it until the door gasket failed and started leaking. After removing the parts, I got on-line and order what I needed. I found everything easier than I thought. I got the parts a few days later and put the gasket in first. Looking at it, you'll find theres slotted ribs at both ends. Those areas go in the bottom corners because of the "S" curve. Simply push in and voila, you're done. At first the door will be firm to shut, but gets better- NO LEAKS! As far as the door spring...you don't have to remove the whole dishwasher. Simply unscrew the bottom plate under the door and reach in, rehook. Piece of cake. This site is wonderful. All the parts and easy to use.

We removed the bottom access panel, and were able to remove the broken spring. As others have suggested, we ordered two new springs, so we could replace them both at the same time. Unlike others, we didn't have to move the dishwasher out a few inches to access the springs. An easier repair than it might have been!

I ordered a new door gasket, wich is not very common for these type of dishwasher anymore, I installed it in less than 15 minutes. I turned the machine on fully loaded and the machine did not leak a single drop. It save me a bundle since I was considering buying a new dishwasher. THANK YOU!!

Unscrewed the dishwasher from counter, located in center front, pulled the dishwasher out, very easy, only about 12 inches, opened the door and saw where the springs went. The spring on the right was missing entirely. Hooked the new springs into place, closed the door, slid the dishwasher back into place. Took about 5 minutes. Thanks to this web site, and the fact that other people had reported how to do the repair. Only cost was that of the springs!

pulled the old gasket out, and pushed the new one into the slot where the old one came out. Very simple repair, and I'm a girl!!

I removed the 2 screws that hold the dishwasher in so I could pull it out. I found out later I didnt need to do this. then I removed the bottom cover and saw the spring that was broken. I removed the spring, hooked the new one into place and I was done.
This was the easiest repair I ever had to do.

Very easy fix, it's the second time I ordered this perticulsr part and it once again prolonged the life of this dishwasher for just a few dollars. The door seal arrived in just a few very short days and was easily installed with no tools in less than 10 minutes. The web site made locating, ordering, and paying for the part needed extremely once again. Thanks

Remove the old gasket simply by pulling it off. I installed the new gasket by starting in one corner and simply pushing the gasket firmly into the groove and working my way around. No tools required. My child could have done it. Problem solved. It takes two or three cycles for the gasket to "break in" and form precisely to the door. Leave the door locked a couple of days to hasten the "break in".

I used the scissors to open the bag the gasket came in. From there it was just seeing how the old, worn gasket was seated in the track around the inside of the dishwasher. Pulling the old one out and snapping the new one in the same way. When I was finished, there was about an inch between the two ends at the bottom where the gasket wasn't quite long enough for them to meet. I was a bit concerned seeing the basin fills with water. So I cut an inch off the best part of the old gasket to fill the space. No leaks! It works great and was so easy to do.

Removed the lower panel (two screws near the floor, two screws with the door open).

Remove screws holding the top of the dishwasher in place.

Remove two screws holding the incoming water switch.

Pull the dishwasher out to access the left side of the dishwasher.

With the door closed remove the spring (replaced both left and right).

Test the motion of the door.

Reverse the process
1. push dishwasher back in
2. Attach water switch bracket
3. Attach top screws that hold the dishwasher in place
4. Replace lower panel
5. Attach screws for lower panel

Test the door motion,

I replaced the gasket a couple of years ago for less than $50. The springs with shipping for less than $25. I wonder how much longer the dishwasher will last. The repairs are easier than putting in a new dishwasher and a whole lot cheaper.

1) Soaked new gasket in hot water for about 15 minutes to make it more pliable. 2) Cleaned accumulated soap residue from gasket area. 3) Removed old gasket by pulling it from machine. 4) Installed new gasket starting at the top and aligning notch on gasket with center of top door latch. 5) Pressed gasket into place working from the top to the bottom. 6) Inspected and found about a half inch gap remained at bottom. 7) Cut a piece of the same size from the old gasket and pressed it in place to close the gap.

Replacement was simple.

This site had good pics and descriptions of the gasket I needed, as well as a LOT of users instructions concerning installation. Ordered, came quickly. It was a little hard to push in the groove. (Maybe a little silicone lube on the gasket would help??) I also filled in the gap at the bottom with a small section of the old gasket, as suggested by (other) installers. Why not? Anyways, it took both hands to close the door the first 3-4 washes. Easy to open/close now. AND... no more leaks! Great price, too!

I removed some philips screws from the kick plate along the bottom of the dishwasher. I then removed some trim screws on the sides of the bottom door panel (the smaller panel below the door on the front of the dishwasher). There were also two screws into the top of the lower panel that you can only see when the door is open. This let me remove the whole lower door panel and kick plate. It was now possible to see the springs on the left and right, and it is actually possible to change them at this point, just with access through the front. However, it is very awkward. Contrary to what some repairs have said, it really is much easier if you can pull the dishwasher out from under the counter about 6 inches. To do that, you'll have to unbolt it, and that will vary depending on how yours was mounted. You may find brackets along the front, screws or bolts through the frame into the floor, and/or retaining straps from the top up to the counter.

Beyond that, it's simple. You'll see that the spring hooks into a slot or hole on a large L-shaped bracket that moves with the door. There is one on each side at the bottom of the door. The other end of each spring hooks through a hole in the frame rail on the bottom. There will likely be several holes, letting you choose how tight you want the spring (this controls how easily the door will drop).
A pair of needlenose pliers is handy for getting the spring end into the holes.

Again, it was a lot easier doing this from the outside of the dishwasher after pulling it out a few inches.