36333355590 Kenmore Cooktop - Instructions

Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl.
Really easy.

Pulled off burner grates, burner, unscrewed burner bowl, removed clip from igniter and wire, then put it all back together. Was very easy, and the stove looks like new again.

PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.

No way to adjust mixer tube assembly so the mounting holes will line up with the holes in the burner bowl. Mounting
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put to much pressure on the side of the hole.

Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.

I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.

I did not get new gaskets for the burner bowl but would reccommend that you get them.

The replacement part not right size for the porcelain cone for gas. Had to unscrew 2 screws remove the cone, after unclicking gas wire. The gas spreader did not fit with the cone in place.

took me a a while to find my problem. One burner would not spark to ignite gas burner. From Part Select website I noticed the part that was the problem from the parts diagram. I did not realize it was related to ignition until I saw that. Easy and cheap to fix after that.

I received a defective part from PartsSelect.com. After contacting their Customer Service, they promptly replaced the part for no charge at all. I am very, very pleased with PartsSelect.com and recommend them to all "home mechanics".

The bowl was replaced by removing two screws, removing the igniter wire, clip, and igniter. Reverse to re-assemble. I would recommend replacing the gasket at the same time.

Real simple to do. Simply remove the two screws holding the bowl and disconnect the electric wire. Obviously first pull the power cord to prevent being shocked.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.

replaced switch

Easy, just remove two top screws, unplug the igniter wire and then do it in reverse. Your're done in less than 15min.

Ok - I LOVE THIS COMPANY!! When I read the other blogs I was a little confused. Ok first choosing the right drip pan for my gas stovetop was a little confusing because there was a cheaper one that look just like mine. I didn't have the model number - so I WOULD have guessed on it. Later I took my stovetop apart and found model number. Found that MY model required the more expensive drip pans. I think this will help people.... (1) Both type of drip pans looked just alike, but the space between the ignitor and the flame was different. The closer one wouldn't have worked. (2) They were categorized as small medium and large drip pans. BUT - they all had the same dimension: 9 inches. The difference is made in the flame area. My stove top has one small flame area, one large and two mediums, that's how you determine which size you need. (3) The ignitor, when you take it off - nothing shows whether the little white ignitor breaks apart or not, and HOW you get it out. Once you remove the little wire holding it to the drippan, don't try to pull apart the white ignitor, it doesn't come apart. Mine had rusty residue attaached, making it hard to pull through. But when I removed the crusty stuff the white thing popped through the hole. (I called a REP to see if the white thing tore apart or not and they weren't sure. So maybe this will help some other woman who is wondering.) This was ABSOLUTELY the easiest and most cost effective way to have a nearly BRAND NEW stove top. And I'm pleased with myself that I did it without any help.

Removed two small screws, removed old bowl, placed new bowl, replaced screws.

Removed two screws holding drip bowl in place. Removed spring clip holding igniter to drip bowl and removed igniter. Installed igniter to new drip bowl and installed drip bowl to cook top. Took less than 5 minutes.

On a scale of 1-10 (1 being the lowest level of difficulty), this was clearly a 1. Tools needed are a plillips' head and flat head screwdrivers. First, lift off Burner Cap and Burner Head. Then, raise existing drip bowl (plenty excess wiring), and use flat screwdriver to release retainer clip. Now, disconnect wire attached to spark electrode (igniter) for removal. Unless replacing it, also remove the rubber gasket at base of old drip bowl for reuse (take the opportunity to clean throughly around drip pan base). Reverse procedure, and check igniter. Your job is complete, and you just saved the cost of a service call, and paid less than half the price of retail for genuine replacement parts. As a side note, I received the parts from PartsSelect in less than 24 hours. The customer reviews will also fully reassure you that you are more than capable of making the simple replacement.

Two screws remove the burner bowl. There is an electric push-on connector for the igniter which is easy to pull off. Remove the igniter retaining clip by pushing it off the igniter with a screwdriver or pulling it off with a pliers. Note that I replaced a Large Burner Drip Bowl and a Small Burner Drip Bowl. THEY ARE THE SAME SIZE. The large and small designation refers to the size of the gas diffuser and ceramic cap. The size difference requires that the hole in the bowl for the igniter be in a different place.

replaced drip bowl removed 2 screws, removed wire from igniter. and could have used a new gasket but I used some rope caulking to cushion the pan with the glass top which worked very very well.