Roper Trash Compactor Parts
Find Parts Fast
Guaranteed Fit
Repair Videos
![Fix.com search Fix.com search](/images/fix-couple.png)
![Roper Appliance Parts](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/images/brands/250/roper.png)
Popular Roper Trash Compactor Parts
- Fix Number
- FIX398589
- Manufacturer Part Number
- 882699
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Drawer is hard to open and or close
- See more...
Installation Instructions
John from RUTHERFORD, NJ
Trash compactor ram was not working.
Watched the video and followed the directions step by step.
Read more...
- Fix Number
- FIX11744742
- Manufacturer Part Number
- WP777811
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
- See more...
Installation Instructions
Chad from Moreno Valley, CA
Trash Compactor would not stop after cycle and would make a ton of noise
I had a couple of problems with my trash compactor, it was present in the home when we bought it. First it wouldn't turn on, the on/off switch was broken so I replaced the switch and knob assembly. Then the unit would run through a cycle and wouldn't stop at the end and would make a loud banging noise. My directional switch was the suspect at first because it was in bad shape to begin with, looked like it had gotten stuck at some point and bent the arm. I replaced the directional switch and it didn't help. Then I realized that the on/off/start panel showed that the start button was stuck in the on position. This was delivering constant current and wouldn't allow the unit to stop. DON'T spend $150 for a new start/on/off panel. I took the panel off and separated the front from the back to expose the buttons from the inside. The start button was stuck so I took the parts out and reassembled them, they're all little plastic and metal pieces that interlink. After I reassembled the buttons' insides I reassembled the panel and reinstalled it. The unit works fine now.
Read more...
- Fix Number
- FIX11747573
- Manufacturer Part Number
- WP9871602
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
Ben from Howell, MI
Trash Compactor the drawer was very hard to open
In replacing the old partial rusted drawer slides had rusted screw with nuts that spun had to drill them out and replaced front larger bolt and nut the rear screw used a larger sheet metal screw. The wheels and bearing with on easy the instructions showed a modification to remove a tab for the different wheel assembly and installed just like the instructions. When done the drawer will slide out with just touch of your foot on open tab GREAT!! I was looking at buying a new compactor the repair saved me about 700 $. Thanks a lot. Never had a trash Compactor before this great and it keeps my puppy out of trash.
Read more...
- Fix Number
- FIX398587
- Manufacturer Part Number
- 882688
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
James from Anchorage, AK
The bar that the rollers fit into has a lip on the front.
The lip on the front of the bar had to be bent so it was almost straight out so a wrench could be put on the nut to remove the old roller. There was not room enough to get on the nut with pliers or wrench and turn it. much more difficult than the instructions laid out.
Read more...
- Fix Number
- FIX382679
- Manufacturer Part Number
- 675382
Fixes these symptoms
- Doesn’t stop at end of compacting cycle
- Won’t start
- Won’t stay on
- See more...
Installation Instructions
Kenneth from New Tazewell, TN
Quit after 38 years. Suggested a switch (s) failure
Removed two screws on front panel which allowed panel to become easily reachable. Replacement of rotary switch kit very simple. Did not replace sectional switch at this time. Back in operation.
Read more...
- Fix Number
- FIX11744741
- Manufacturer Part Number
- WP777533
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- See more...
Installation Instructions
Diane from Norton, MA
compactor would not compact and come back up to the starting position
First of all I would like to thank this site for the excellent service we received and the young lady I spoke to in customer service was great. Only the right side was bad, but I changed both sides while I was at it. I left the left side in tacked so I could get the right height on the right side to make sure the ram was level. I took of the two nuts and undid the power nut. At this point I cleaned off the screw rod that the power nut attaches to and screw on the new power nut. I had someone hold up the back of the ram to make sure that I had it level and then put on the cap and attached it with the two small screws, and then repeater the same steps for the left side. Tis compactor is thirty six years old and this is the first time I did any repairs to it and I hope it last another thirty six.
Read more...
- Fix Number
- FIX11743097
- Manufacturer Part Number
- WP608732
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
Gordon from Clearwater, FL
Broken upper handle
Slide open the unit door and identify the screws holding the door handle in place. Using a Phillips screwdriver, remove the (2) screws holding the handle in place. Remove (lift up and out) the broken piece or pieces, replace with the pricey new one and put the screws back in. (Screw holes are pre-drilled to match in the pricey new handle.
Read more...
- Fix Number
- FIX11742478
- Manufacturer Part Number
- WP4387911
Fixes these symptoms
- Light not working
- See more...
Installation Instructions
HARRY from KNOXVILLE, TN
DROPPED BOWL ON LEVER OF SWITCH AND SNAPPED IT OFF
PULLED OUT THE OLD SWITCH WITH A LITTLE PRESSURE AND SIDE PANEL FLEXED OUT ENOUGH TO PUT FINGER IN AND BEHIND THE BAD SWITCH TO PUSH IT OUT. THEN READ INFO TO KNOW MY SWITCH WAS NORMALLY OFF WHEN DOOR WAS CLOSED SO I WIRED IT AS INSTRUCTED AND POPPED THE NEW SWITCH BACK INTO THE SLOT. HAD TO ARANGE THE WIRING BEHIND IT TO ALLOW THE SWITCH TO LIE FLUSH IN SLOT SO IT WAS NOT PUSHED OUT FROM BEHIND AGAINST FOAM INSULATION.
Read more...
- Fix Number
- FIX3652693
- Manufacturer Part Number
- W10439651
Installation Instructions
Scott from Derby, KS
Motor Failed On Unit
New motor arrives and is designed as a replacement across several models. It was necessary to replace all the wire end and crimp on the supplied smaller spade terminals. Only issue was the wire length on the unit was short and made it tough to reach. Followed the instructions for placement and result was great. Took me about 21/2 hours to complete
Read more...
- Fix Number
- FIX11744740
- Manufacturer Part Number
- WP777383
Installation Instructions
Chad from Moreno Valley, CA
Trash Compactor would not stop after cycle and would make a ton of noise
I had a couple of problems with my trash compactor, it was present in the home when we bought it. First it wouldn't turn on, the on/off switch was broken so I replaced the switch and knob assembly. Then the unit would run through a cycle and wouldn't stop at the end and would make a loud banging noise. My directional switch was the suspect at first because it was in bad shape to begin with, looked like it had gotten stuck at some point and bent the arm. I replaced the directional switch and it didn't help. Then I realized that the on/off/start panel showed that the start button was stuck in the on position. This was delivering constant current and wouldn't allow the unit to stop. DON'T spend $150 for a new start/on/off panel. I took the panel off and separated the front from the back to expose the buttons from the inside. The start button was stuck so I took the parts out and reassembled them, they're all little plastic and metal pieces that interlink. After I reassembled the buttons' insides I reassembled the panel and reinstalled it. The unit works fine now.
Read more...