Models
>
NX58H5600SS
NX58H5600SS ((AA-00)) Samsung Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for NX58H5600SS
Viewing 5 of 5Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
On Order
$86.67
The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
On Order
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for NX58H5600SS
Viewing 3 of 3Little to no heat when baking
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/4240743_1_S.jpg)
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/4241428_1_S.jpg)
How to fix it
Element will not heat
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/4241428_1_S.jpg)
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from EAST QUOGUE, NY
- Parts Used:
- DG94-00520A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven not heating and holding temp
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the c
... Read more
enter of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from CHICAGO, IL
- Parts Used:
- DG61-00570A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
REPLACED THE FLOOR CAVITY
REMOVED THE TWO SCREWS AND THEN THE FLOOR PIECE. THEN REPLACED THE NEW FLOOR CAVITY AND SCREWED THE NEW ONE IN PLACE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CHEYENNE, WY
- Parts Used:
- DG32-00002B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat consistently
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the
... Read more
issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
Read less
Was this instruction helpful to you?
Thank you for voting!