Models
>
1071-003A
1071-003A Frigidaire Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 1071-003A
Viewing 11 of 11
Keep searches simple, eg. "belt" or "pump".
This heating element mounting nut is used in dishwashers and is used to hold the nut to prevent leaking. If your nut is damaged or you notice leaking from the dishwasher, then replacing this nut will ...
In Stock
$7.85
This is a single rack roller kit for your dishwasher. This kit comes with one axel/clip, and one wheel/roller. The kit is used for the lower dishrack, and allows your rack to move freely. You will nee...
In Stock
In Stock
$30.35
NOTE: Sold individually. This door spring is four and a half inches long. It is used for some dishwashers. These springs tend to wear out at the same rate, so you should replace both of your dishwashe...
In Stock
In Stock
$28.69
This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into speci...
In Stock
Special Order
$85.28
This electrically operated propeller causes water to flow through your dishwasher's pump. This impeller is located above the dishwasher's mascerator blade.
In Stock
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
No Longer Available
This white rinse aid cap is a little over two inches long. It comes with a black rubber gasket, and is used for some dishwashers.
No Longer Available
$41.14
With this macerator blade it chops up/mince the food particles in the collection chamber to prevent from clogging the dishwasher pump.
In Stock
$10.79
This black pump housing spacer plate is a little under four inches long.
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 1071-003A
Viewing 4 of 4Leaking
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Tryon, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Water leaking under the dishwasher
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa
... Read more
sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from New Orleans, LA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water leak underneath dishwasher
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from mcdonough, GA
- Parts Used:
- 5300809606
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The inlet water valve was leaking into the dishwasher.
Pulled the dishwasher out. Removed the lower face panel , two screws on the top of panel and two screws on the bottom of the panel. Removed the two screws that hold the water valve and removed the valve, installed the new valve , installed the lower panel, put the dishwasher back in it`s position , turned on the water and checked for lea
... Read more
ks, ran the dishwasher through a cycle , job done. Thanks to partselect for finding me the correct valve, my dishwasher is 12 years old and nobody else on the internet could help me get the right valve. Good price and fast shipping.
Read less
Was this instruction helpful to you?
Thank you for voting!